Zontes ZT184MN Скачать руководство пользователя

Страница: 24 / 54

4-RIGHT CRANKCASE COVER ASSEMBL

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

4050454-014051

ZT180MN fine filter cover A (dark gray)

1051454-020000

55×2.5 Hydrogenated nitrile rubber O-ring

1051454-005000

ZT180MN Oil filter sealing ring

Outer diameter Φ50×47 cylindrical fine filter

1050853-009000

Φ16.4×17×1.6 filter spring

1051161-012000

M24×2 oil filler plug

1051461-007000

25×3.1 Hydrogenated nitrile rubber O-ring

Fig.2 RIGHT
CRANKCASE COVER

Remove Right Crankcase Cover Assembly 2

1251300-096000

Non-standard cover type 9 degree nut M6×
13 (environmental color Zinc)

12±1.5N.m

【

】

4134300-001000

ZT184MP fine filter sealing assembly(carton
packaging)

PROCEDURE:

●

Fine filter assembly

Use a 10# sleeve to remove the 3 nuts

⑴

, remove the fine filter cover

⑵

, O-ring

⑶

sealing ring

⑷

, fine filter

⑸

, spring

⑹

●

Oil plug

Hold the oil plug

⑺

by hand and turn it counterclockwise to take out the O-ring

⑻

Notice:

●

When replacing the fine filter

⑸

, the O-ring 3 and the sealing ring

⑷

must be replaced,

otherwise there will be oil seepage and other phenomena.

●【

】

O-ring

⑶

, sealing ring

⑷

, fine filter

⑸

are all included in the fine filter sealing

component

⑽

, do not need to be purchased separately.

●

It is strictly forbidden to lift the fine filter cover with hard objects, otherwise it will cause

oil leakage.

●

Check whether the O-ring is damaged. If it is damaged, replace it immediately, otherwise

it will cause oil leakage.

●

Do not install the Fine filter upside down. The end face of the filter element with the

"OUT-SIDE" mark faces the fine filter cover.

●

The hole on the fine filter cover

①

should be aligned with the hole on the right cover

②

when installing.

●

You can watch the detailed operation in "ZT350 Replacing Fine Filter Video".

Содержание ZT184MN























































Результаты поиска

Содержание ZT184MN

Отзывы:

Похожие инструкции для ZT184MN

Бренды по названию

Популярные бренды

Zontes ZT184MN, Руководство по обслуживанию

Результаты поиска

Содержание ZT184MN

Отзывы:

Похожие инструкции для ZT184MN

Бренды по названию

Популярные бренды