Zontes ZT184MN Скачать руководство пользователя

Страница: 23 / 54

4-RIGHT CRANKCASE COVER ASSEMBL

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251112-004093

M6×60 Hexagon flange bolts (color Zinc)

1251513-001019

6.3×12×1.6 copper gasket

1251112-003093

M6×45 Hex flange surface 9.8 bolt (color Zinc

1251112-006093

M6×90 Hexagon flange bolts (color Zinc)

1251112-005093

M6×75 Hexagon flange bolts (color Zinc)

1051354-008000

ZT180MN clutch cable bracket

1251401-001000

φ8×14 hollow locating pin

1050854-007000

φ6×6 hollow positioning pin

1051354-012000

9.2×18×1 Thrust Washer

Fig.1 RIGHT
CRANKCASE COVER

Remove Right Crankcase Cover Assembly 1

1051658-008000

ZT184MP Gasket for right crankcase cover
(foaming rubber)

PROCEDURE:

●

Remove the right crankcase cover

Fix the engine, use an 8# sleeve to remove 3 bolts (1) with a copper washer (2), 6 bolts (3),

1 bolt (4) and 1 bolt (5); take out the Clutch cable bracket(6).

Separate the right crankcase cover sub-assembly from the engine case, and remove the

gasket

⑺

, 2 locating pins

⑻

, and 1 locating pin

⑼

,Water pump shaft washer 9.2x18x1

⑽

Notice:

●

The gasket

⑺

is for one-time use and must be replaced after disassembly.

●

Before installing the box body, make sure that the box body assembly plane is smooth

and flat and apply an appropriate amount of sealant on the box body assembly plane. After
installing the new gasket

⑺

, it is necessary to apply sealant again on the upper surface of

the Install new gasket

⑺

●

When installing the right cover, all bolts should be evenly tightened at the corners to

ensure tightness.

Содержание ZT184MN























































Результаты поиска

Содержание ZT184MN

Отзывы:

Похожие инструкции для ZT184MN

Бренды по названию

Популярные бренды

Zontes ZT184MN, Руководство по обслуживанию

Результаты поиска

Содержание ZT184MN

Отзывы:

Похожие инструкции для ZT184MN

Бренды по названию

Популярные бренды