Zontes ZT184MN Скачать руководство пользователя

Страница: 29 / 54

4-RIGHT CRANKCASE COVER ASSEMBL

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1050754-007000

ZT180MN clutch spring pressure plate

1050758-002000

ZT184MP clutch spring

1051454-017000

ZT180MN sliding clutch cushion rubber

1050754-006000

ZT180MN clutch release lever

1050754-023000

ZT180MN sliding clutch friction plate sub-asse

1251514-006000

96.5×107×2.2×1 gasket

Flat gasket

1251512-031000

96.3×107×7 thrust washer

Butterflywasher

PROCEDURE:

●

Clutch assembly

Use an 8# sleeve to remove 3 bolts (1), and take out the pressure plate (2) and 3 springs

(3).Pull out the buffer rubber

⑷

, the pressure plate

⑸

, and take off the separation rod

⑹

Take out the friction plate sub-assembly

⑺

, lock washer

⑻

, thrust washer

⑼

. The edge of

the lock washer

⑻

is chamfered.

Notice:

●

When installing, the side of the lock washer with lettering should face outward.

●

When disassembling the bolts, loosen them one by one. Try to keep the bolts from having

too much height difference, otherwise the parts may bounce off under the action of the
spring. The installation should also be tightened one by one.

●

Check the wear of each part of the clutch, and replace the defective parts with serious

wear.

Fig.7 RIGHT
CRANKCASE COVER

Remove the clutch1

1251100-070093

M6×30 flange full thread bolt(graped
9.8/environmental color)

1050754-024000

ZT180MN sliding clutch pressure plate sub-
assembly

Содержание ZT184MN























































Результаты поиска

Содержание ZT184MN

Отзывы:

Похожие инструкции для ZT184MN

Бренды по названию

Популярные бренды

Zontes ZT184MN, Руководство по обслуживанию

Результаты поиска

Содержание ZT184MN

Отзывы:

Похожие инструкции для ZT184MN

Бренды по названию

Популярные бренды