Zonar V3 Скачать руководство пользователя страница 3

Страница: 3 / 28

EVIR

• V3

™

Introduction .......................................................................................2

System Overview ...............................................................................4

V3 Equipment....................................................................................5

Optional Equipment - EVIR

...............................................................6

General Guidelines.............................................................................7

V3 Mounting Plate .............................................................................8

V3 Pin Configuration ..........................................................................9

Power and Data Connections.....................................................10-11

4 Pin Cable Testing ..........................................................................12

GPS 4 Pin Power Cable Management .............................................12

Wiring Guidelines .............................................................................13

Antenna Installation..........................................................................14

GPS VM and Tag Installation............................................................15

GPS System Check .........................................................................16

System Checklist .............................................................................17

System Specifications......................................................................18

Equipment Dimensions...............................................................19-20

Installation Examples ..................................................................21-22

System Installation Diagram.............................................................23

Discrete I/O System Installations.................................................24-25

Warranty & Notices - FCC Compliance ............................................26

Notes...............................................................................................27

TABLE OF CONTENTS

Products and services protected by one or more of the following US patents: 6,671,646;

6,804,626; 7,557,696; 7,117,121; 7,362,229; 7,564,375; 7,680,595; 7,776,499;

7,808,369; 7,944,345; 8,106,757, plus EP 2756504.3 and the AU.

REV: 07/31/12

Содержание V3




























Результаты поиска

Содержание V3

Отзывы:

Zonar V3, Руководство пользователя и инструкция по установке, Страница: 3 / 28

Результаты поиска

Содержание V3

Отзывы: