Zonar V3 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 28

Zonar V3 Скачать руководство пользователя страница 18

System Specifications

V3™

• Operating Temp -40C to +85C
• DC Input range, 8Vdc to 30Vdc

GPS Receiver

• Hybrid GPS/SBAS engine (WAAS, EGNOS, MSAS)
• Very high sensitivity receiver
• Rapid acquisition of satellites
• GPS signal acquisition, tracking and navigation
• On board GPS data storage

GSM/GPRS Transceiver

• GSM (2G) 850/900/1800/1900 MHz
• WCDMA (3G) 850/1900 MHz

Approved External GPS Antennas

• San Jose SM-19 - GPS

Important Notice

It is the Owner's sole responsibility to install and use the Zonar
products in a manner that will not cause accidents, personal injury
or property damage. For the purposes of this notice, "Owner",
"you" and "your" means the party (including any person authorized
by that party to use and/or install the Product) that has either: (a)
purchased the Product; or (b) leased the Product from Zonar
Systems, Inc or its related companies. The Owner of this product
is solely responsible for observing safe driving practices. The
choice, location, and installation of all components of the Product
is critical. If installation is not correct, the Product may not perform
at its designed potential or specifications. If in doubt, consult your
vehicle's manufacturer.

SYSTEM SPECIFICATIONS

18

«
...
16
17
18
19
20
...
»

Содержание V3





























Отзывы:

Нет отзывов