background image

22

Messages

Meaning

Solution

Check Salt 

Check Minerals

Your salinity level 

may be low

Take a water sample to the pool shop to see if your 

salt or mineral levels need topping up. Please note 

that this can be affected by low water temperatures. 

If the water temp is below 21ºC it is imperative that 

you check the salinity before adding extra salt/

minerals

Check Cell

Cell may be 

approaching end 

of life

Contact your local pool care professional to ask 

about a replacement cell

Check Pump

Pumps output is 

off due to pump 

protection being 

activated

Check to see if there is water flow through the cell 

housing,  if  there  is  no  flow  or  very  low  flow  there 

may be a problem with the pump, or the pump is 

disconnected. Ensure all electrical connections 

are in place and there is no blockage in the pipe. 

Manually turn the chlorinator on to clear the warning

No Flow

Too little or no 

flow 

of 

water 

through the cell 

housing. Chlorine 

production is 

halted when 

this warning is 

displayed

Check to see if there is water flow through the cell 

housing,  if  there  is  no  flow  or  very  low  flow  there 

may be a problem with the pump, or the pump is 

disconnected. Ensure all electrical connections are 

in place and there is no blockage in the pipe

Check Pwr 

Supply

Power pack has 

over heated or 

encountered a 

problem

This warning may appear when the power supply has 

over heated and needs time to cool down. It could be 

triggered due to very high ambient temperatures or 

there may be a heat source nearby (remove the heat 

source if possible). If the problem persists you may 

need seek help from a pool care professional

Cell Cleaning

Cell has gone into 

reversing mode to 

clean

This represents the cell is going through its normal 

cleanng cycle. There is no need to do anything when 

this message is displayed

Boost

Cell is in 100% 

production mode

This message represents that the unit is at 100% 

output for a 24 hour period

Low

Cell is in 10% 

production mode

This message represents that the unit is at 10% 

output

MESSAGES AND WARNINGS. WHAT THEY MEAN.

Содержание TRi-XO CROSSOVER

























Отзывы: