Zip HydroTap 3-in-1 Скачать руководство пользователя страница 19

Page 19 of 24 

                                   

HydroTap Installation and Operating Instructions_Commercial_BCH 4in1_BH 3in1_October 2012_V1.05

 Boiling Water Isolation

The HydroTap is equipped with an additional safety mode that allows 
protection against accidental operation by Infirm or disabled persons.

1.  On the LCD scroll through the menu to Hot Isolation.

2.  Press adjust 

>

 to activate.

3.  Now go to the Tap Head assembly and press the Safety Lock (3) three 

times rapidly, the LED’s will scroll from left to right (3) three times.  
This operation confirms the activation.

4.  This isolates the boiling tap only. The LCD shows isolation mode is active.

5.  To temporarily de-actvate and dispense boiling water, press the Safety 

Lock (3) three times rapidly, the LED’s will scroll from right to left (3) 
three times. This operation confirms de-activation and will temporarily 
de-activated. After 30 seconds of no use the unit will revert to normal 
active mode.

6.  If permanent de-activation is required, de-activate by scrolling through 

the menu and selecting de-activate when Hot isolation Mode is displayed 
on the screen. 

7.  The LCD will show Normal Operation.

Set The Boiling & Chilled Water Dispensing Times

The ability to change the maximum dispensing time for both the Boiling and 
Chilled water has been introduced. The default settings for the maximum 
dispensing times is 15 secs. The ability to change both the Boiling and Chilled 
dispensing times between 5 and 15 secs, in increments of 1 sec, is accessible 
through the Menu screen on the LCD.

Scroll through the Menu until the Dispense Hot screen is displayed, then use 
the adjust buttons to set the required dispensing time for the Boiling water.

Follow the same procedure to access the Dispense Cold (for Chilled water) 
screens.

Cleaning

Do not use strong, corrosive, spray or abrasive cleaners. Clean with a soft 
cloth or brush and mild soap and water.

Do not spray water over the tap as it may damage the low-voltage electronics.

Undersink units must never be located near, or cleaned with water jets.

In order to help preserve our environment we ask that you dispose of this 
product correctly. 

Please contact Zip Customer Service on 0845 6 005 005 for advice.

End of Life Disposal

Содержание HydroTap 3-in-1

























Отзывы: