Zinwell ZPlus-B191-OD Скачать руководство пользователя страница 3

Страница: 3 / 41

This EUT is incompliance with SAR for general population /uncontrolled exposure limits in

ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and

procedures specified in OET Bulletin 65 Supplement C

This device and its antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter

CAUTION

：

1. The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent

structures with a separation distance of at least 2 meters from all persons and must

not be co-located or operating in conjunction with any other antenna or

transmitter.

Users and installers must be provided with antenna installation

instructions and transmitter operating conditions for satisfying RF exposure

compliance.

2. This Transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

3. This equipment is only allowed to be professionally installed.

Содержание ZPlus-B191-OD










































Результаты поиска

Содержание ZPlus-B191-OD

Отзывы:

Похожие инструкции для ZPlus-B191-OD

Бренды по названию

Популярные бренды

Zinwell ZPlus-B191-OD, Руководство пользователя

Результаты поиска

Содержание ZPlus-B191-OD

Отзывы:

Похожие инструкции для ZPlus-B191-OD

Бренды по названию

Популярные бренды