Zimmer GEP2000IO-00 страница 39 Скачать руководство пользователя

Страница: 39 / 56

Error code

Error

Possible cause

Measure

0x0000

Device is ready for operation.

0x0002

Position measuring system not

referenced.

•

Product does not have any

reference position.

►

Please contact Zimmer

Customer Service.

0x0003

Device is booted up.

•

The device is in the start

sequence.

►

Wait until the start sequence

is complete.

0x0100

Actuator power supply is not

present or is too low

•

Actuator power supply is not

connected

•

Actuator power supply is not

sufficient

•

Cable break

►

Check the actuator power

supply.

0x0101

Temperature above maximum

permitted temperature.

• Ambient temperature is too

high.

•

Overload of the products.

►

Provide sufficient ventilation/

cooling/connection.

►

Check that the product

moves freely.

0x0102

Temperature is below minimum

permitted temperature.

• Ambient temperature is too

low.

►

Provide an adequate

operating temperature.

0x0103

Temperature of the power level

is too high

• Surrounding temperature is

too high

•

Overload of the product

•

Internal defect

►

Ensure improved cooling of

the product.

►

Check that the product

moves freely.

►

Increase the break time

between the gripping

movements.

0x010B

Workpiece lost

•

Gripping force is not

sufficient

•

Workpiece was not gripped

correctly

• Gripper finger geometry

does not match the gripped

workpiece

•

Workpiece is too heavy

►

Check the required gripping

force.

►

Check the gripper finger

geometry.

►

Reset the error by sending

another move command

back.

0x0300

ControlWord is not plausible.

•

Multiple bits were set in the

ControlWord.

►

In the ControlWord, check

that only one bit is set.

0x0301

Position implausible

• Transmitted TeachPosition is

not plausible.

►

Check the transmitted

process data.

• Permissible range,

depending on installation

size: Jaw stroke x 200

Example: GEP2016 with jaw

stroke of approx. 16.1 mm

results in a value of 3220.

0x0302

GripForce is not plausible.

• Transmitted GripForce is not

plausible.

►

Check the transmitted

process data.

0x0304

PositionTolerance is not

plausible.

• Transmitted PositionTol

erance is not plausible.

►

Check the transmitted

process data.

0x0305

Erroneous reference position

•

Product does not have any

reference position.

►

Please contact Zimmer

Customer Service.

0x0306

DeviceMode is not plausible.

• Transmitted DeviceMode is

not plausible.

►

Check the transmitted

process data.

14 Error diagnosis

INSTALLATION AND OPERATING INSTRUCTIONS:

GEP2000

DDOC01113 / b

EN / 2022-05-01

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

Содержание GEP2000IO-00

























































Результаты поиска

Содержание GEP2000IO-00

Отзывы:

Похожие инструкции для GEP2000IO-00

Бренды по названию

Популярные бренды

Zimmer GEP2000IO-00, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GEP2000IO-00

Отзывы:

Похожие инструкции для GEP2000IO-00

Бренды по названию

Популярные бренды