Zimmer GEP2000IO-00 страница 8 Скачать руководство пользователя

Страница: 8 / 56

5 Product description

CAUTION

Reduction of the gripping force can cause personal injury and material damage

When flexible components are gripped, the gripping force of the product is reduced.
Reduced gripping force can lead to personal injury or material damage, because the components that are being

gripped can no longer be securely gripped and transported.

NOTICE

►

Make sure that the setting of the gripping force and the selection of the gripper finger length are correct to

prevent incorrect bracing of the gripper jaws.

An incorrect configuration or selection can lead to malfunction

5.1 Possible applications

outside gripping

inside gripping

The product can be used for outside gripping.

The product can be used for inside gripping.

MoveToWork command

MoveToBase command

5.2 Forces and torques
INFORMATION

►

You can find the information in the technical data sheet on our website.

►

Please contact Zimmer Customer Service if you have any questions.

5.3 Type plate

A type plate is attached to the housing of the product.

XXX

XX-XXXXXX

The article number and confirmation number are shown on the type

plate.

Article number

Confirmation number

INSTALLATION AND OPERATING INSTRUCTIONS:

GEP2000

DDOC01113 / b

EN / 2022-05-01

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

Содержание GEP2000IO-00

























































Результаты поиска

Содержание GEP2000IO-00

Отзывы:

Похожие инструкции для GEP2000IO-00

Бренды по названию

Популярные бренды

Zimmer GEP2000IO-00, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GEP2000IO-00

Отзывы:

Похожие инструкции для GEP2000IO-00

Бренды по названию

Популярные бренды