manualshive.com logo in svg

Zimmer GED5000IL Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Zimmer GED5000IL Series Скачать руководство пользователя страница 46

Zimmer GmbH 

•

 Am Glockenloch 2 

•

 77866 Rheinau, Germany 

•

 

 

+49 7844 9138 0 

• 

 +49 7844 9138 80 

•

 www.zimmer-group.com

46

INSTALLATION AND OPERATING IN-

STRUCTIONS:

GEP5000/GED5000 electric gripper series

EN / 05/01/2021

DDOC00211/i

13 Maintenance

Maintenance-free operation of the gripper is guaranteed for up to 

30 million cycles

.

The maintenance interval may shorten under the following circumstances:
•  Dirty environment
• 

Improper use and use that does not comply with the power specifications.

• 

Observe the ambient temperature; lubricants harden faster!

Even though the product is maintenance-free as mentioned above, perform a regular visual inspection to check for any 

corrosion, damage or contamination.
We recommend allowing maintenance and seal replacement to be carried out by Zimmer Customer Service. 
Dismantling and reassembling the product without authorization may result in complications as special installation 

equipment is required in some cases.

13.1 Safety notice

CAUTION

Material damage due to improper vacuuming

 

►

Never purge the product with compressed air.

 

Ö

Risk of accident, malfunction

Material damage caused by liquid and solvent-based cleaners

 

►

Do not clean the product with any cleaning agents that are liquid or contain solvents.

 

Ö

Risk of accident, malfunction

Содержание GED5000IL Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды