manualshive.com logo in svg

Zimmer GED5000IL Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Zimmer GED5000IL Series Скачать руководство пользователя страница 43

Zimmer GmbH 

•

 Am Glockenloch 2 

•

 77866 Rheinau, Germany 

•

 

 

+49 7844 9138 0 

• 

 +49 7844 9138 80 

•

 www.zimmer-group.com

43

INSTALLATION AND OPERATING IN-

STRUCTIONS:

GEP5000/GED5000 electric gripper series

EN / 05/01/2021

DDOC00211/i

11.2 Troubleshooting display for GEP5000IO/GED5000IO

Error code

Error

Possible cause

Measure

1

5

Gripper is ready for operation

No error

-

-

1

5

Motor has slight overcurrent in multi-

ple consecutively following cycles

• 

Gripper is difficult to move

•  Travel path of the gripper is 

impeded

•  Object being gripped or gripper 

fingers are elastic

•  Check the gripper's freedom 

of movement

•  Check the object being 

gripped and the gripper 

fingers

1

5

Motor has strong excess current

•  Gripper is jammed
•  Internal error

•  Restore the gripper's freedom 

of movement

 

►

 Zimmer Customer Service

1

5

Motor has excess current in idle 

mode

•  Internal error

 

►

 Zimmer Customer Service

1

5

Temperature of the motor output 

stage above the limit value

•  Surrounding temperature too 

high

•  Gripper is overloaded

• 

Provide for sufficient 

ventilation/cooling

•  Check the object being 

gripped and/or the gripper 

fingers

1

5

Gripper is in reference run mode

•  Internal error

 

►

 Zimmer Customer Service

1

5

Gripper has no reference on the jaw 

position

•  Gripper has lost its reference 

position

 

►

 Zimmer Customer Service

1

5

Motor is in setting run mode at the 

end position

•  Setting run was started
•  CAUTION: do not evaluate the 

positions during the setting run!

•  Wait for completion of the 

setting process

1

5

Gripper does not reach the end 

position

(Work, teach and base position)

•  Gripper does not reach the work, 

teach and base position

•  Check the object being 

gripped and/or the gripper 

fingers

Содержание GED5000IL Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды