manualshive.com logo in svg

Zimmer GED5000IL Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
Zimmer GED5000IL Series Скачать руководство пользователя страница 41

Zimmer GmbH 

•

 Am Glockenloch 2 

•

 77866 Rheinau, Germany 

•

 

 

+49 7844 9138 0 

• 

 +49 7844 9138 80 

•

 www.zimmer-group.com

41

INSTALLATION AND OPERATING IN-

STRUCTIONS:

GEP5000/GED5000 electric gripper series

EN / 05/01/2021

DDOC00211/i

11 Error diagnosis

11.1 Troubleshooting display for GEP5000IL/GED5000IL

Error code Error

Possible cause

Measure

0x0

No error

-

-

0x100

Actuator power supply is not 

present or is too low.

•  Actuator power supply is not 

connected.

•  Cable break
•  Actuator power supply is not 

sufficient.

 

►

Check the actuator power 

supply.

0x101

Temperature above maximum 

permitted temperature.

•  Ambient temperature is too 

high.

•  Overload of the products.

 

►

Provide sufficient ventilation/

cooling/connection.

0x102

Temperature below minimum 

permitted temperature.

•  Ambient temperature is too low.

 

►

Ensure a sufficient operating 

temperature.

0x300

The configured "ControlWord" is 

implausible.

•  Multiple bits are set in 

"ControlWord."

 

►

Only one bit is permitted to be 

active in "ControlWord."

0x301

The configured "TeachPosition" is 

outside the permitted range.

•  Incorrect value on the 

"TeachPosition."

 

►

Check the "TeachPosition" 

parameter.

 

►

Permissible range, depending 

on design size.

 

►

Maximum position value 

corresponds to the jaw stroke 

x 200.

0x302

The configured gripping force is 

outside the permitted range.

•  Incorrect value in the 

"GripForce" parameter.

 

►

Check the "GripForce" 

parameter.

 

►

Permitted range: 0 < 

"GripForce" ≤ 4

0x304

The configured tolerance value is 

outside the permitted range.

•  Incorrect value in the "Position-

Tolerance" parameter.

 

►

Check the "PositionTolerance" 

parameter.

 

►

Permitted range: 0 < "Position-

Tolerance" ≤ 255

0x305

The device has an incorrect 

reference position.

•  Product does not have any 

reference position.

 

►

 Zimmer Customer Service

0x306

The configured "DeviceMode" is 

implausible.

•  Incorrect value in the 

"DeviceMode" parameter.

 

►

Adjust the "DeviceMode"

 

►

Universal = 100

 

►

Grip workpiece outside = 60

 

►

Grip workpiece inside = 70

Содержание GED5000IL Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды