manualshive.com logo in svg

Zepro ZS 150-135, Инструкция по установке

Поделиться
Скачать
Zepro ZS 150-135 Скачать руководство пользователя страница 46

46

8. Connection unit

Power save mode

If the control card is not used for a certain amount of time, it goes into power save mode.

Time with CS off = 5 min - CS on = 20 min. With CS on, press any control button for approx. 0,5 seconds 

 to 

“wake up” the control card again.

Operating information

All the lift’s functions are controlled and monitored through the control card, which is equipped with an 

alphanumerical display with a flashing light and 2 red LEDS. These display current operating information. 

In the event of any operational disturbances, fault codes are displayed to facilitate troubleshooting.

The display indicates:

-  Active control device

-  Fault display

-  Program configuration

-  Sensors’ current status

Flashing light indicates:

-  Supply voltage

-  Off: No supply voltage

-  On: Supply voltage available but CS (cabin switch) is not active.

-  Flashing: CS (cabin switch) is active, the system is awaiting input signal.

LED 1 indicates: 

-  Active input, button(s) on control device pressed.

LED 2 indicates:

-  Active output (approved input signal from control device and sensors), the lift is operated.

The control card is equipped with an alphanumerical display with a flashing light and 2 red LEDS

Display

Flashing light

LED 2

LED 1

Содержание ZS 150-135































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды