manualshive.com logo in svg

Zepro ZS 150-135, Инструкция по установке

Поделиться
Скачать
Zepro ZS 150-135 Скачать руководство пользователя страница 33

33

Please refer to the instructions for electrical 

installation regarding ancilliary equipment from 

your vehicle supplier.

Install control units at suitable places, but the posi-

tion of the control unit should ensure that the ope-

rator has a good view of the load, the working area 

and the loading area, whilst maintaining a safe  

distance from the risk zone between the platform 

and the body. Note that all cables must be connec-

ted from below so that water can´t get into the units 

but condensation can drain out.

Fixed control units are normally electrically heated. 

The heating cable must be well earthed. Note that 

12 V (black) and 24 V (red) has different heating 

cables.

All control units must be connected in parallel.

The control cable is connected to the circuit card in 

the connection unit (see electric diagram).

Install the control current cable from the dashboard 

of the truck according to the customers require-

ments. The control current swich should be located 

so it is possible to be reached from the ground 10 A 

(24 V), 15 A (12 V) fuse between the current source 

and the switch.

The control current cable is connected to a fixed 

control unit. You can fasten the cable together with 

the main cable to the hydraulic unit.

Connect the main power cable to the starter motor 

(B+) of the truck, never to the battery. The cable 

should be protected with a plastic sheath. It must not 

be fastened together with brake pipes or other elec-

tric cables of the truck. When passing through holes 

the cables must be protected with rubber bushings.

A 160 A (24 V) or 250 A (12 V) fuse is to be installed 

on the main power cable running from the battery 

compartment**. This acts to protect the electrical 

systems from overloading and the risk of fire

If you have a spiral cable unit, its cable colours are 

different (see electric diagram):

If you want an electrically heated spiral cable 

unit you can order a 5 - part cable (spare-part no 

21303). Note that the spiral cable unit must have its 

fastening plate for the wall (spare-part no 20302).

Check that the hydraulic unit is well earthed accor-

ding to truck manufacturer´s instructions.

If you must lead a spiral cable up through the floor 

you must protect it with a sheath up from the floor.

If you need to use power from the circuit card +ve 

connection point a fuse must be installed, eg. over-

load alarm 7.5 Ampere.

Test run all functions from all control units. 

 

Alarm for open platform

The alarm consists of a warning lamp (which should 

be placed clearly visible in the driver cabin), which 

illuminates when the ignition key is turned on, and 

the lift platform is not pressed up against the under-

side of the chassis

The device consists of:

*Pressure guard placed on the lift cylinder circuit.

*Cable to the dash board

*Fuse

*Warning lamp 12 alt. 24 Volt

Alarm for open platform (trailer)

The alarm consists of a warning lamp (which should 

be placed on the body of trailer, clearly visible so 

that the driver can see it in the rear mirror), which 

illuminates if the lift platform is not pressed up 

against the underside of the chassis

Anordningen består av:

*Pressure guard placed on the lift cylinder circuit.

*Cable to the dash board

*Fuse

*Warning lamp 12 alt. 24 Volt

5. Electrical installation

NB. The quick connectors must be well protected 

and should be positioned inside the vehicle chassis.

**Note! The fuse should be placed on a well pro-

tected place and as near as possible to the battery.

Содержание ZS 150-135































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды