Zelmer ZVC415 Series, Руководство пользователя

Страница: 45 / 47

45
ZVC415-002_v02
3 Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/pull the tube
together.
4 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5 Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according to
the figure . Retract the brush when vacuuming carpets
(set the switch in “ ”).
6
Grab the plug (6) and pull the cord out of the vacuum
cleaner.
7 Plug in the appliance.
Before operation make sure that the SAFBAG bag is
installed in the vacuum cleaner chamber and that inlet filter
and the EPA outlet filter is installed in the appliance.
8 Switch on the vacuum cleaner by pressing the “on/off”
button (1) .
9 The vacuum cleaner is equipped with an electronic
power control which allows to gradually adjust the vacuum
cleaner suction power during operation. To adjust the
suction power use the power adjustment buttons (8,10)
– to increase the suction power or – to decrease the
suction power. The suction power setting is indicated by the
appropriate number of lit diodes.
The vacuum cleaner is equipped with a power
level memory function. When you turn off the
vacuum cleaner using the ON/OFF button
(1), the power level is going to be stored in
memory. After the vacuum cleaner is turned
on next time, it is going to start working at the
same power level it had been working before it
was turned off.
The suction power may be adjusted during operation.
The recommended settings are:
Setting 1 – vacuuming curtains
Setting 2 – vacuuming upholstery
Setting 3 – vacuuming carpets
Setting 4 – vacuuming hard floors and crevices
Setting 5 – maximum suction power.
The power may also be adjusted individually depending on
the type of surface, vacuum effectiveness and suction power
of the switchable combination brush.
The vacuum cleaner is equipped with the
adjustment function for LED brightness of the
power level indicator (9) on the control panel.
In order to set a demanded LED brightness,
you have to press both of the power adjustment
buttons (8) and (10), and when still
pressing these buttons turn on the vacuum
cleaner by pressing the ON/OFF button (1). The
LED for power levels 1, 3, and 5 turn on, and
the motor stays turned off. Next by pressing
the power adjustment buttons (8) and
(10) you can respectively increase or decrease
the brightness of power level indicator (9).
After setting a desired LED brightness, it is
necessary to turn off the vacuum cleaner using
the ON/OFF button (1). In this way you leave
the LED brightness adjustment function mode,
and the set LED brightness level is stored.
10
The vacuum cleaner is equipped with an accessory
compartment. To open the compartment lift the vacuum
cleaner handle and pull the accessory compartment cover
(5) upwards.
11
The accessories may be attached to the accessory
holder in the suction hose handle. This way they will be
available for use at any time.
Filter disassembly
Before changing the filters make sure that the vacuum cleaner
is switched off and unplugged from the mains supply.
INLET FILTER
1
Release the front cover fastening (12) and open the cover.
2 Slide the inlet filter (15) from the appliance body.
3
Insert the new filter making sure that the outer edge of
the filter is located to the inside of the limiting rib.
4 Close the front cover.
EPA OUTLET FILTER
The vacuum cleaners are equipped with an E11 outlet filter
EPA.
1 To replace the EPA filter lift the vacuum cleaner handle
and open the accessory compartment.
2
Grab the outlet filter cover (7) by the two fastenings,
press firmly with the thumbs and pull it to the outside.
3 Remove the EPA filter case and replace it with a new
one. The EPA filter ensures an effective operation of the
vacuum cleaner for about 1 year.
4
Insert the cover so that the two protrusions in the lower
part of the cover are inserted in the openings of the vacuum
cleaner body, press the filter cover so that the rear fastenings
snap shot on the body.
●
Close accessory storage.
SAFBAG dust bag disassembly/assembly
E
1 The vacuum cleaner is equipped with a safety valve
which is located in the dust container (bag) chamber.
It opens automatically when the suction hose or the elements
attached to the suction hose are completely clogged or when
the dust bag is overfilled with dust. After the opening of the
valve a characteristic “fluttering” in the vacuum cleaner will
be heard. The opening of the safety valve will result in the
lighting of the dust bag full indicator.
2
When the dust bag full indicator (11) lights (with the
nozzle or the brush lifted above the cleaned surface) it means
C
D