45
ZVC012ZQ-001_v01
3 IN 1 BRUSH
14
3 in 1 brush consists of a crevice nozzle, small nozzle and
brush - attachment for the small nozzle. The accessories can
be used to:
●
Crevice nozzle is used for cleaning: corners, stairs,
keyboards and other hard to reach recesses.
●
Small nozzle is used for vacuuming sofas, couches,
beds, etc.
●
By attaching the brush onto the small nozzle, you get the
perfect accessory for dusting furniture, shelves, curtains,
etc.
●
By combining the above-mentioned accessories, you
get the 3 in 1 brush. This combination will increase the
vacuuming possibilities.
Battery charging
D
Before charging, make sure the appliance is switched off.
1
Connect the charging station with the base.
●
Place the complete charging station near the wall
socket.
2
Plug the appliance into the wall socket.
3
Place the vacuum cleaner on the charging station
(the hand vacuum cleaner must be attached to the housing).
4
After placing the vacuum cleaner on the charging station,
the “ON” indicator light located on the hand vacuum cleaner
will light up red, indicating that the vacuum cleaner batteries
are being charged.
5
Batteries charging cycle is from 6 to 8 hours. After this
time, the “ON” indicator light on the hand vacuum cleaner
should change from red to green, indicating that the vacuum
cleaner batteries are charged.
It is recommended to continue charging for another 1-2
hours.
●
Once the vacuum cleaner batteries have been charged,
unplug the power cord plug from the wall socket.
●
In order to keep the vacuum cleaner ready for use, it is
recommended to leave it in the charging station when
not in use.
●
When batteries are fully charged the vacuum cleaner will
operate for 20 minutes maximum.
During three initial charging cycles the
batteries should be fully discharged, and the
charging time should be at least 12 hours in
order to obtain the maximum battery charge.
Subsequent charging can be carried out in the
manner described above.
When voltage drops down, the vacuum cleaner
will automatically switch off, therefore it is
recommended to keep it fully charged before
use.
End of operation, cleaning and maintenance
DUST CONTAINER AND FILTER UNIT CLEANING
1
To remove the dust container press the release button
and gently pull the container downwards.
2
Remove the “CYKLON” container with the installed EPA
filter. In order to do so, hold the grip of the filter unit and
remove it from the container.
3
Empty the dust container.
4
Wash the inside of the dust container with lukewarm
water and dry it with a cloth.
Clean the dust container after each use.
5
Remove the EPA filter from the filter unit.
When clogged by dirt, the EPA filter should be
cleaned or replaced.
6
Clean the creases of EPA filter. Filter can be washed
under running water. Before reassembly, dry the filter
accurately. In case of filter crease damage, it should be
absolutely replaced with a new one.
7
Open the “CYKLON” container, empty it and clean the
cyclone cone. The “CYKLON” container can be washed
under running water. Before reassembling, dry the container
accurately.
8
Once the EPA filter and the “CYKLON” container have
been dried, put both elements together. In order to do so,
insert the EPA filter in its slot. Insert the filter unit into the dust
container.
Due to safety reasons, wet or damaged filter
must not be installed.
9
Install the dust container with the filter unit onto the
hand vacuum cleaner housing. Characteristic clicking sound
indicates the correct installation of the dust container.
ELECTROBRUSH CLEANING
During operation, the electrobrush roller collects pieces
of: threads, strings, hair, rags, etc. They reduce cleaning
efficiency, therefore it is necessary to periodically clean the
electrobrush roller.
In order to remove dirt from the electrobrush roller, follow the
steps below:
1
In order to disconnect the brush from the vacuum cleaner
housing, press the electrobrush release button.
2
With a flat, narrow object, such as coin or screwdriver,
turn the cover lock from closed position „ ” to open position
„
”. Remove the cover and take out the roller.
3
Carefully clean the electrobrush roller with scissors or
sharp knife. Move the scissors or the knife so as to catch
the hair or threads tangled on the roller. Cut them and then
remove from the roller.
E
F
Содержание zvc012zq
