Zelmer zts1510w, Руководство пользователя

Страница: 34 / 36

38
TS1100-001_v03
When the toaster is switched on and used for
the first time, select position 3 (standard set -
ting). Different bread types and individual pref -
erences may require different settings.
With the same browning degree, one slice
of bread will be toasted better than two slices
of bread toasted simultaneously.
During continuous toasting, subsequently pre -
pared toasts will be more browned than those
prepared in the first cycle.
3
To insert bread into the toaster, slide the lever down until
it locks into position. Toasting cycle will start.
The lever will only lock when the appliance
is connected to the power supply.
The browning degree may be observed dur -
ing toasting. When the bread is sufficiently
browned, the toasting cycle may be stopped at
any time by pressing the CANCEL button.
4 After the toasting cycle has ended, the lever will auto -
matically slide up to the initial position.
To facilitate smaller bread slices removal, lift
the lever up – above the initial position.
If the bread is not sufficiently toasted, another
toasting cycle may be run. Select light brown -
ing (adjustment slide in a 1 or 2 position) and
then push the toasting lever down until it locks
into position. Control the browning degree
to ensure the toasts would not burn.
●
Remove the toasts, be careful not to touch any hot surface.
If bread slices are stuck in the toaster, press
the CANCEL button and pull out the plug from
the socket. Wait until the toaster cools down
completely and carefully move the bread
so that no heating elements are damaged.
Additional features
FROZEN BREAD TOASTING
Place the frozen bread slices in the bread slots, select the
desired degree of browning. Slide the bread slices down into
the toaster by pushing the lever down until it locks into posi -
tion and press the DEFROST button. The button will light up.
Frozen bread toasting takes more time than
thawed bread.
BREAD REHEATING
This toaster enables bread reheating, irrespectively of the
selected browning degree. Place the toasts in the bread
slots. Slide the bread slices down into the toaster by push -
ing the lever down until it locks into position and press the
REHEAT button. The button will light up.
Notes on toasting
Toasting is a combination of bread roasting and drying.
Humidity levels vary for different types of bread, which may
cause differences in the time of toasting.
●
For slightly dry bread, use a setting lower than the standard.
●
For fresh or wheat bread, use a higher setting than the
standard.
●
Bread with a very uneven surface will require a higher
setting.
●
Toasting thicker pieces of bread will last longer, because
before toasting the bread needs to remove more mois -
ture. Very thick pieces may require two toasting cycles.
Cleaning and maintenance of the
toaster
1 Before cleaning, always switch off the toaster, pull out the
plug from the socket and wait until it cools down completely.
2
To remove the bread crumbs from the toaster, remove
the bread crumb tray located at the bottom of the toaster.
Empty it and place it in the same position as previously.
Do not use the toaster with no bread crumb
tray in place.
3
To remove the bread crumbs from inside of the toaster,
turn the toaster upside down and gently shake the bread
crumbs out.
4 The external surfaces clean with a soft, slightly damp
cloth and wipe dry.
Do not allow excessive accumulation of bread
crumbs in the tray. Bread crumb tray should be
cleaned regularly.
Ecology – Environment protection
Each user can protect the natural environ -
ment. It is neither difficult nor expensive.
In order to do it: put the cardboard packing
into recycling paper container; put the poly -
ethylene (PE) bags into container for plastic.
When worn out, dispose the appliance to particular disposal
centre, because of the dangerous elements of this appli -
ance, which can be hazardous for natural environment.
Do not dispose the appliance with the municipal waste!
C
The manufacturer does not accept any liability for any damages
resulting from unintended use or improper handling.
The manufacturer reserves his rights to modify the product any time
in order to adjust it to law regulations, norms, directives, or due to
construction, trade, aesthetic or other reasons, without notifying in
advance.