Zelmer 32z012, Руководство пользователя

Страница: 27 / 30

29
Important safety instructions
Read the whole instruction for use before you start using
●
your stand blender.
The stand blender is intended for domestic usage only.
●
In case it is used for gastronomic business purposes,
warranty terms and conditions change.
Connect the appliance to 230 V mains supply.
●
Always place the appliance on flat, plain surface.
●
Always unplug the appliance when it is not in use and
●
before cleaning.
Do not unplug by pulling on cord.
●
The supplying cord shall not be hanged over the edge of
●
the table or board, nor touch any hot surface.
Do not operate the appliance if the cord, the housing or
●
the handle is visibly damaged. In such a case, return the
appliance to a service center.
If the non-detachable part of the cord is damaged,
it should be replaced by the producer or at a proper
service point or by a qualified person in order to avoid
any hazards.
The appliance can only be repaired by qualified service
personnel. Improper servicing may cause a serious
hazard to the user. In case of defects please contact
a qualified service center.
Do not immerse motor housing in water or any other
●
liquid; do not use it in bathroom and outdoors.
Press „
●
OFF ” button, before you remove the lid of the jug
and remove the jug from the motor housing, wait until the
blades stop completely.
Do not use stand blender without feeder opening
●
stopper.
Do not fill the jug in with boiling liquids.
●
Do not put your hands inside the jug, even if it is removed
●
for cleaning, as the cutting blades are still dangerous –
very sharp.
Do not put any objects (spoon, etc.) into the jug, when
●
the blender is connected to power supply.
Keep the jug blender and supplying cord away from hot
●
surfaces and burners.
If it is possible, store the stand blender away from direct
●
sun radiation and glow-like light.
Never store with lid closed on the blender jug. Damp the
●
lid gasket with water before usage, and insert the lid on
the jug.
Do not overflow the jug. In case the liquid gets under
●
the motor housing, it can be vacuumed into the motor,
causing its damage.
Do not fill the jug over 1500 ml mark – in such case, the
●
content of the jug can lift the lid when the motor starts up
After 2 minutes operation stop the appliance for at least
●
minute to let the motor cool down. You can repeat this
cycle maximum10 times.
Do not operate when the jug is empty, as it can get
●
overheated.
Do not wash the cutting blades directly with hand.
●
Use the soft brush for washing metal parts, especially
●
the sharp blades.
This appliance is not intended for use by persons
●
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not
●
play with the appliance.
The temperature of mixed ingredients should not exceed
●
60°C.
Make sure you understand well above mentioned
instructions.
Specifications
You can find the appliance technical data on the name plate.
Admissible time of non-stop operation: 3 minutes.
An interval between repeated operations: 10 minutes.
Maximum noise level: 80 dB/A.
The stand blender is built in II class of insulation .
It does not require connecting to mains supply socket with
earthing.
The stand blender meets the requirements of effective
standards.
The appliance meets the requirements of the following
directives:
Low Voltage Device (LVD) – 2006/95/EC.
–
Electro- Magnetic Compatibility (EMC) – 2004/108/EC.
–
The product is marked with CE symbol on the name plate.
Outline (Fig. A)
1 Lid sieve
2 Speed I
3 ICE
4 ON/OFF
5 Speed II
6 CLEAN/PULSE
7 Feeder opening stopper
8 Lid
9 Blender jug
10 Motor housing
11 Control panel
12 Anti-slip flange
13 Blocking ring
14 Blades
15 Gasket
EN