York YST Скачать руководство пользователя страница 21

Страница: 21 / 164

JOHNSON CONTROLS

SECTION 2 - OPTIVIEW CONTROL CENTER INTRODUCTION

FORM 160.67-O1

ISSUE DATE: 4/1/2015

hoMe SCreen

LD09257

figure 6 -

HOME SCREEN

noTe:

OptiView

™

Control Center Screens shown may NOT represent the exact screens according to the software version utilized.

overvieW

When the chiller system is powered on, the above de-

fault display appears. The primary values which must

be monitored and controlled are shown on this screen.

The Home Screen display depicts a visual represen-

tation of the chiller itself. The chilled and condens-

er liquid flow lines are animated whenever adequate

flow has been established to close the respective flow

switch. The turbine steam inlet flow line is animated at

speeds above 500 RPM.

diSplaY onlY
Chilled liquid Temperature - leaving

Displays the temperature of the liquid as it leaves the

evaporator.

Chilled liquid Temperature - return

Displays the temperature of the liquid enters the evapo-

rator.

Condenser liquid Temperature - leaving

Displays the temperature of the liquid as it leaves the

condenser.

Condenser liquid Temperature - return

Displays the temperature of the liquid as it enters the

condenser.

operating hours

Displays the cummulative operating hours of the chill-

er.

Turbine Speed

The turbine speed is sensed by two magnetic pickups

that monitor a toothed gear installed on the turbine

shaft. The pickup signals are converted to 4-20 mA

signals by frequency-to-analog converters in the

Turbine Box and connected to the Analog I/O Board in

the Control Center. This data field displays the highest

of the two speed input signals.

Steam flow

Displays the rate of steam flowing through the turbine.

This text and data field only appears if FSE1-Steam

Flow Sensor Enable is set for Enabled on Configura-

tion Screen 2.

Chilled liquid flow

Displays the rate of chilled liquid flowing through the

evaporator. This text and data field only appears if

FSE1- Evaporator Flow Sensor Enable is set for En-

abled on Configuration Screen 2.

Condenser liquid flow

Displays the rate of cooling liquid flowing through

the condenser. This text and data field only appears

if FSE3-Condenser Flow Sensor Enable is set for En-

abled on Configuration Screen 2.

Содержание YST





































































































































































Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды

York YST, Руководство по эксплуатации

Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды