York YST Скачать руководство пользователя страница 79

Страница: 79 / 164

JOHNSON CONTROLS

SECTION 2 - OPTIVIEW CONTROL CENTER INTRODUCTION

FORM 160.67-O1

ISSUE DATE: 4/1/2015

SeTpoinTS SCreen

LD09260

figure 28 - SeTpoinTS SCreen

noTe:

OptiView

™

Control Center Screens shown may NOT represent the exact screens according to the software version utilized.

overvieW

This screen provides a convenient location for pro-

gramming the most common setpoints involved in the

chiller control. This screen also serves as a gateway to

a sub-screen for defining the setup of general system

parameters alarm and shutdown setpoints, and miscel-

laneous configuration.

diSplaY onlY

Leaving Chilled Liquid Temperature -

Setpoint Dis-

plays the present setpoint to which the chiller is operat-

ing whether controlled remotely or locally. This value

could come from a 0-20 mA, 4-20 mA, 0-10VDC or

2-10VDC input in Analog Remote mode, PWM signal

in Digital Remote mode, MicroGateway interface in

ISN mode, or a locally programmed value.

leaving Chilled liquid Temperature Cycling -

Shutdown

Displays the Leaving Chilled Liquid Temperature at

which the chiller will shut down to avoid over-cool-

ing the building. This value is calculated by subtract-

ing the Leaving Chilled Liquid Temperature Cycling

Offset – Shutdown from the Leaving Chilled Liquid

Temperature – Setpoint. If this value is below the abso-

lute minimum allowed shutdown temperature the mini-

mum value is displayed.

leaving Chilled liquid Temperature Cycling –

restart

Displays the Leaving Chilled Liquid Temperature at

which the chiller will restart after it has shut down due

to over-cooling temperature. This value is calculated

by adding the Leaving Chilled Liquid Temperature Cy-

cling Offset – Restart to the Leaving Chilled Liquid

Temperature – Setpoint.

prograMMable
local leaving Chilled liquid Temperature -

range

Access Level Required

: OPERATOR

This is the range over which an analog signal (0-20

mA, 4-20 mA, 0-10VDC or 2-10VDC) in Analog Re-

mote Mode or a digital signal (PWM) in Digital re-

mote mode can reset the Leaving Chilled Liquid Tem-

perature setpoint above the operator programmed

Base

Setpoint (see below). Programmable as either 10°F or

20°F, with a default of 20°F, it is added to the

BASE

value to create a range over which the remote device

can reset the setpoint. For example, if this setpoint is

programmed for 10°F and the operator programmed

value is 45°F, then the remote device can set the Leav-

ing Chilled Liquid Temperature setpoint over the range

45.0°F - 55.0°F.

Содержание YST





































































































































































Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды

York YST, Руководство по эксплуатации

Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды