York YST Скачать руководство пользователя страница 82

Страница: 82 / 164

JOHNSON CONTROLS

FORM 160.67-O1

ISSUE DATE: 4/1/2015

SECTION 2 - OPTIVIEW CONTROL CENTER INTRODUCTION

12/24 hr

Access Level Required

: OPERATOR

Allows the user to specify the format in which the time

will be presented to the user. This setpoint will affect

the display of the time on the chiller panel and on all

reports generated. 12-Hour time format will include the

and

modifiers and show the range of time be-

tween 1:00 and 12:59, while the 24-Hour time format

will show the range of time between 0:00 and 23:59.

Change Settings

Access Level Required

: SERVICE

This key allows the following chiller parameters to be

programmed:

liquid Type

Access Level Required

: TEST OPERATOR/ADMIN-

ISTRATOR
Displays

Water

Brine

Chilled liquid pump operation

Displays

Standard

Enhanced

power failure restart

Displays

Manual

Automatic

pre-lube

Displays

Standard

(50 seconds) or

Extended

(180

seconds)

Compressor oil pump package

Displays

Fixed

Speed

Variable

Speed

Compressor Model

Access Level Required

: TEST OP / ADMIN

The Horsepower Limit PID setpoint is initially set to

the maximum allowable for the Compressor Model en-

tered here. It is entered at the factory and can only be

changed in the TEST OP or ADMIN access level.

inlet Steam pressure range

Access Level Required:

Test OP/Admin

The inlet steam pressures range is entered at the factory

and can only e changed in the test OP or Admin access

level. Rage setting is 0-150PSIG, 0-300 PSIG or 0-500

PSIG.

Panel will be automatically booted for

changes to take affect.

navigaTion
home

Access Level Required

: VIEW

Causes an instant return to the Home Screen.

diagnostics

Access Level Required

: SERVICE

Moves to the sub-screen allowing limited diagnostic

capability while operating. Refer to YORK Service

Manual 160.67-M3

Comms

Access Level Required

: VIEW

Moves to the sub-screen allowing configuration of sys-

tem communications.

printer

Access Level Required

: VIEW

Moves to the sub-screen allowing configuration and

control of printer functions.

Sales order

Access Level Required

: VIEW

Moves to the sub-screen displaying the Sales Order in-

formation for the chiller system.

operations

Access Level Required

: VIEW

Moves to the sub-screen displaying operating param-

eters of the chiller system.

user

Access Level Required

: VIEW

Moves to the sub-screen allowing configuration of user

preferences.

Содержание YST





































































































































































Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды

York YST, Руководство по эксплуатации

Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды