York YST Скачать руководство пользователя страница 93

Страница: 93 / 164

JOHNSON CONTROLS

SECTION 2 - OPTIVIEW CONTROL CENTER INTRODUCTION

FORM 160.67-O1

ISSUE DATE: 4/1/2015

This is only used when the turbine is supplied with an

auxiliary oil pump and MSSP6-Turbine Lubrication

Type is set for Pump on the Configuration Screen 1.

An immediate shutdown is initiated if the input signal

from the Turbine Supply Oil Pressure Transmitter is

below this setpoint. This check is bypassed for the first

45 seconds of the prelube after the message “START

SEQUENCE INITIATED” is displayed.

PSP16 - Turbine Inlet Steam High Pressure Alarm

Screen: Steam System

Range: 100.0-500.0 PSIG

Default: 500.0 PSIG

An alarm is generated if the input signal from the Tur-

bine Inlet Steam Pressure Transmitter is above this

setpoint.

SSp8 – overspeed Shutdown

Screen: Auto/Manual
Range: 3600-4900 RPM

Default: 4900 RPM

An immediate shutdown is initiated if the higher of the

two speed analog input signals from the frequency-to-an-

alog converters in the Turbine Box is above this setpoint.

TSp4 - Turbine Shaft end bearing high

Temperature alarm

Screen: Turbine

Range: 180.0-220.0 °F

Default: 210.0 °F

This is only used when the turbine is supplied with

bearing RTD sensors and MSSP14-Turbine Bearing

Temperature Sensors is set for Enabled on the Con-

figuration Screen 1. An alarm is generated if the input

signal from the Turbine Shaft End Bearing RTD Tem-

perature Transmitter is above this setpoint. The final

setpoint should be 5-10 °F higher than the normal op-

erating temperature of the bearing.

TSp5 - Turbine Shaft end bearing high

Temperature Shutdown

Screen: Turbine

Range: 180.0-220.0 °F

Default: 220.0 °F

This is only used

when the turbine is supplied with

bearing RTD sensors and MSSP14-Turbine Bearing

Temperature Sensors is set for Enabled on the

Configuration Screen 1.

An immediate shutdown is

initiated if

the input signal from the Turbine Shaft

End Bearing RTD Temperature Transmitter is above

this setpoint.

The final setpoint should be 5-10 °F

higher than the normal operating temperature of

the bearing.

TSp6 - Turbine governor end bearing high

Temperature alarm

Screen: Turbine

Range: 180.0-220.0 °F

Default: 210.0 °F

This is only used when the turbine is supplied with

bearing RTD sensors and MSSP14-Turbine Bearing

Temperature Sensors is set for Enabled on the Con-

figuration Screen 1. An alarm is generated if the input

signal from the Turbine Governor End Bearing RTD

Temperature Transmitter is above this setpoint. The fi-

nal setpoint should be 5-10 °F higher than the normal

operating temperature of the bearing.

TSp7 - Turbine governor end bearing high

Temperature Shutdown

Screen: Turbine

Range: 180.0-220.0 °F

Default: 220.0 °F

This is only used when the turbine is supplied with

bearing RTD sensors and MSSP14-Turbine Bearing

Temperature Sensors is set for Enabled on the Con-

figuration Screen 1. An immediate shutdown is initi-

ated if the input signal from the Turbine Governor End

Bearing RTD Temperature Transmitter is above this

setpoint.

The final setpoint should be 5-10 °F higher

than the normal operating temperature of the bear-

ing.

TSp8 - Turbine Supply oil high Temperature

alarm

Screen: Turbine

Range: 110.0-135.0 °F

Default: 130.0 °F

This is only used when the turbine is supplied with an

auxiliary oil pump and MSSP6-Turbine Lubrication

Type is set for Pump on the Configuration Screen 1. An

alarm is generated if the input signal from the Turbine

Supply Oil RTD Temperature Transmitter is above this

setpoint.

TSp8 - Turbine Supply oil high Temperature

Shutdown

Screen: Turbine

Range: 110.0-135.0 °F

Default: 135.0 °F

This is only used when the turbine is supplied with an

auxiliary oil pump and MSSP6-Turbine Lubrication

Type is set for Pump on the Configuration Screen 1.

An immediate shutdown is initiated if the input signal

from the Turbine Supply Oil RTD Temperature Trans-

mitter is above this setpoint.

Содержание YST





































































































































































Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды

York YST, Руководство по эксплуатации

Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды