York YST Скачать руководство пользователя страница 29

Страница: 29 / 164

JOHNSON CONTROLS

SECTION 2 - OPTIVIEW CONTROL CENTER INTRODUCTION

FORM 160.67-O1

ISSUE DATE: 4/1/2015

CondenSer SCreen

00302VIP

figure 9 - CondenSer SCreen

noTe:

OptiView

™

Control Center Screens shown may NOT represent the exact screens according to the software version.utilized.

overvieW

This screen displays a cutaway view of the chiller con-

denser. All setpoints relating to the condenser side of

the chiller are maintained on this screen. Animation of

the liquid flow lines indicate condenser liquid flow.

diSplaY onlY
leaving Condenser liquid Temperature

Displays the liquid temperature as it leaves the condens-

er.

return Condenser liquid Temperature

Displays the liquid temperature as it enters the con-

denser.

Condenser pressure

Displays the refrigerant pressure in the condenser.

Condenser liquid flow

Displays the rate of cooling liquid flowing through

the condenser. This text and data field only appears

if FSE3-Condenser Flow Sensor Enable is set for En-

abled on Configuration Screen 2.

Condenser Saturation Temperature

Displays the saturation temperature in the condenser.

Small Temperature difference

Displays the difference between the Condenser Refrig-

erant temperature and the Leaving Condenser Liquid

temperature. The Condenser Refrigerant temperature

will be represented by the Condenser Saturation tem-

perature.

drop leg refrigerant Temperature

Displays the temperature of the refrigerant in the drop

leg between the condenser and evaporator shells, if the

sensor is present.

Sub-Cooling Temperature

Displays the difference between the Condenser Refrig-

erant temperature and the Drop Leg Refrigerant tem-

perature. The Condenser Refrigerant temperature will

be represented by the Condenser Saturation tempera-

ture. If the Drop Leg sensor is not present, this tem-

perature is not displayed.

high pressure Switch (open / Closed)

Displays the present position of the high pressure

switch. This will indicate whether a High Pressure

fault is present.

Condenser liquid flow Switch

Indicates whether flow is present in the condenser.

Содержание YST





































































































































































Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды

York YST, Руководство по эксплуатации

Результаты поиска

Содержание YST

Отзывы:

Похожие инструкции для YST

Бренды по названию

Популярные бренды