manualshive.com logo in svg

York MAXE OPTIVIEW YK, Инструкция по эксплуатации

"York MAXE OPTIVIEW YK" - высококачественный продукт с длинным сроком службы от York. Для точной установки и обслуживания необходимо скачать бесплатное руководство по обслуживанию на manualshive.com. Это "Service Instructions Manual" поможет вам получить максимальную производительность от вашего оборудования.

Поделиться
Скачать
background image

FORM 160.54-M1(503)

105

YORK INTERNATIONAL

FIG. 58 – 

LEAVING CHILLED LIQUID TEMPERATURE (CONT’D.)

  

Temp (°F)    Temp (°C)        Vin

     

44.46             6.92        2.6019 

     

44.55             6.97        2.6049 

     

44.64             7.02        2.6080 

     

44.73             7.07        2.6110 

     

44.82             7.12        2.6141 

     

44.91             7.17        2.6171 

     

45.00             7.22        2.6202 

     

45.09             7.27        2.6232 

     

45.18             7.32        2.6263 

     

45.27             7.37        2.6293 

     

45.36             7.42        2.6324 

     

45.46             7.48        2.6354 

     

45.55             7.53        2.6385 

     

45.64             7.58        2.6415 

     

45.73             7.63        2.6446 

     

45.82             7.68        2.6476 

     

45.91             7.73        2.6507 

     

46.00             7.78        2.6537 

     

46.09             7.83        2.6568 

     

46.18             7.88        2.6598 

     

46.27             7.93        2.6629 

     

46.36             7.98        2.6659 

     

46.45             8.03        2.6690 

     

46.55             8.08        2.6720 

     

46.64             8.13        2.6751 

     

46.73             8.18        2.6781 

     

46.82             8.23        2.6811 

     

46.91             8.28        2.6842 

     

47.00             8.33        2.6872 

     

47.09             8.38        2.6903 

     

47.18             8.43        2.6933 

     

47.27             8.48        2.6964 

     

47.36             8.53        2.6994 

     

47.45             8.58        2.7025 

     

47.55             8.64        2.7055 

     

47.64             8.69        2.7086 

     

47.73             8.74        2.7116 

     

47.82             8.79        2.7147 

     

47.91             8.84        2.7177 

     

48.00             8.89        2.7208 

     

48.09             8.94        2.7238 

     

48.18             8.99        2.7269 

     

48.27             9.04        2.7299 

     

48.37             9.10        2.7330 

     

48.46             9.15        2.7360 

     

48.55             9.20        2.7391 

     

48.64             9.25        2.7421 

     

48.74             9.30        2.7452 

     

48.83             9.35        2.7482 

     

48.92             9.40        2.7513 

     

49.01             9.45        2.7543 

     

49.11             9.51        2.7574 

     

49.20             9.56        2.7604 

     

49.29             9.61        2.7635 

     

49.38             9.66        2.7665

  

Temp (°F)    Temp (°C)        Vin

     

39.57             4.21        2.4342 

     

39.66             4.26        2.4372 

     

39.74             4.30        2.4403 

     

39.83             4.35        2.4433 

     

39.92             4.40        2.4464 

     

40.01             4.45        2.4494 

     

40.10             4.50        2.4525 

     

40.19             4.55        2.4555 

     

40.27             4.59        2.4586 

     

40.36             4.64        2.4616 

     

40.45             4.69        2.4647 

     

40.54             4.74        2.4677 

     

40.63             4.79        2.4708 

     

40.71             4.84        2.4738 

     

40.80             4.89        2.4769 

     

40.89             4.94        2.4799 

     

40.98             4.99        2.4830 

     

41.07             5.04        2.4860 

     

41.16             5.09        2.4891 

     

41.24             5.13        2.4921 

     

41.33             5.18        2.4952 

     

41.42             5.23        2.4982 

     

41.51             5.28        2.5012 

     

41.60             5.33        2.5043 

     

41.69             5.38        2.5073 

     

41.78             5.43        2.5104 

     

41.87             5.48        2.5134 

     

41.96             5.53        2.5165 

     

42.05             5.58        2.5195 

     

42.14             5.63        2.5226 

     

42.23             5.68        2.5256 

     

42.31             5.73        2.5287 

     

42.40             5.78        2.5317 

     

42.49             5.83        2.5348 

     

42.58             5.88        2.5378 

     

42.67             5.93        2.5409 

     

42.76             5.98        2.5439 

     

42.85             6.03        2.5470 

     

42.94             6.08        2.5500 

     

43.03             6.13        2.5531 

     

43.12             6.18        2.5561 

     

43.21             6.23        2.5592 

     

43.30             6.28        2.5622 

     

43.39             6.33        2.5653 

     

43.48             6.38        2.5683 

     

43.57             6.43        2.5714 

     

43.65             6.47        2.5744 

     

43.74             6.52        2.5775 

     

43.83             6.57        2.5805 

     

43.92             6.62        2.5836 

     

44.01             6.67        2.5866 

     

44.10             6.72        2.5897 

     

44.19             6.77        2.5927 

     

44.28             6.82        2.5958 

     

44.37             6.87        2.5988

  

Temp (°F)    Temp (°C)        Vin

      49.48             9.71        2.7696 
      49.57             9.76        2.7726 
      49.66             9.81        2.7757 
      49.75             9.86        2.7787 
      49.84             9.91        2.7818 
      49.94             9.97        2.7848 
      50.03           10.02        2.7879 
      50.12           10.07        2.7909 
      50.22           10.12        2.7940 
      50.31           10.17        2.7970 
      50.40           10.22        2.8001 
      50.50           10.28        2.8031 
      50.59           10.33        2.8062 
      50.68           10.38        2.8092 
      50.78           10.43        2.8123 
      50.87           10.48        2.8153 
      50.96           10.53        2.8184 
      51.06           10.59        2.8214 
      51.15           10.64        2.8245 
      51.24           10.69        2.8275 
      51.34           10.75        2.8306 
      51.43           10.80        2.8336 
      51.52           10.85        2.8367 
      51.62           10.90        2.8397 
      51.71           10.95        2.8428 
      51.80           11.00        2.8458 
      51.90           11.06        2.8458 
      51.99           11.11        2.8519 
      52.09           11.16        2.8549 
      52.18           11.21        2.8580 
      52.28           11.27        2.8610 
      52.37           11.32        2.8641 
      52.46           11.37        2.8671 
      52.56           11.42        2.8702 
      52.65           11.47        2.8732 
      52.75           11.53        2.8763 
      52.84           11.58        2.8793 
      52.94           11.63        2.8824 
      53.03           11.68        2.8854 
      53.13           11.74        2.8885 
      53.22           11.79        2.8915 
      53.32           11.85        2.8946 
      53.41           11.90        2.8976 
      53.51           11.95        2.9007 
      53.60           12.00        2.9037 
      53.70           12.06        2.9068 
      53.79           12.11        2.9098 
      53.89           12.16        2.9129 
      53.98           12.21        2.9159 
      54.08           12.27        2.9190 
      54.17           12.32        2.9220 
      54.27           12.37        2.9251 
      54.36           12.42        2.9281 
      54.46           12.48        2.9312 
      54.55           12.53        2.9342

18

Содержание MAXE OPTIVIEW YK





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAXE OPTIVIEW YK

hillvert HT-HECTOR 212 User Manual preview
HT-HECTOR 212
Бренд: hillvert Страницы: 37
Honda FF500 Owner'S Manual preview
FF500
Бренд: Honda Страницы: 282
York YCAS Installation Operation & Maintenance preview
YCAS
Бренд: York Страницы: 216
Troy-Bilt GARDEN WAY Pro line 12183 Owner'S Manual preview
GARDEN WAY Pro line 12183
Бренд: Troy-Bilt Страницы: 36
Troy-Bilt Bronco 634F Operator'S Manual preview
Bronco 634F
Бренд: Troy-Bilt Страницы: 32
Troy-Bilt 769-03618 Operator'S Manual preview
769-03618
Бренд: Troy-Bilt Страницы: 48
Vito Agro VIME7 Instruction Manual preview
VIME7
Бренд: Vito Agro Страницы: 72
Craftsman 917.299691 Owner'S Manual preview
917.299691
Бренд: Craftsman Страницы: 32
Ferrari 346 Quick Manual preview
346
Бренд: Ferrari Страницы: 17
Trane Sintesis Advantage CGAF 100 SE Installation Operation & Maintenance preview
Sintesis Advantage CGAF 100 SE
Бренд: Trane Страницы: 88
Trane CONQUEST CGAX 015 Installation Operation & Maintenance preview
CONQUEST CGAX 015
Бренд: Trane Страницы: 56
Trane RTAA-130 Installation, Operation And Maintenance Manual preview
RTAA-130
Бренд: Trane Страницы: 140
Trane R Series Installation Operation & Maintenance preview
R Series
Бренд: Trane Страницы: 188
Filtrine 5311/05 Manual preview
5311/05
Бренд: Filtrine Страницы: 33
MTD 217-250 Owner'S Manual preview
217-250
Бренд: MTD Страницы: 8
MTD 215-355AB2 Owner'S Operating Service Instruction Manual preview
215-355AB2
Бренд: MTD Страницы: 14
Daikin FWKE Series Technical Manual preview
FWKE Series
Бренд: Daikin Страницы: 86
A.B.Energy ABE 300 Operating Instructions Manual preview
ABE 300
Бренд: A.B.Energy Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды