York MAXE OPTIVIEW YK Скачать руководство пользователя | Manualshive

Страница: 127 / 180

background image

FORM 160.54-M1(503)

127

YORK INTERNATIONAL

20

When the OPEN or CLOSE key is pressed, the valve
position will be increased or decreased by 5% to a max-
i mum of 100% or minimum of 0%. Each time either key
is pressed, the LED in the respective key will illuminate
for 2 seconds. The Hot Gas Bypass Control Mode will
display “Manual”.

ANALOG I/O BOARD

The optional Analog I/O Board mounts inside the Con-
trol Center, on the upper right hand side of the Control
Center. It receives the Hot gas valve positioning com-
mand from the Microboard over the RS-485 serial
com mu ni ca tions link and converts this digital value to
a 2-10VDC analog control signal that is applied to the
valve actuator. The scaling of this signal is as described
above. Valve position is displayed on the HOT GAS
BYPASS Screen as 0% (closed) to 100% (fully open).
Positions between these extremes are linearly scaled.

The Pre-rotation Vanes (PRV) potentiometer (2.5K
Ohms) is connected to P1, providing a 0 to 5VDC volt-
age from a +12VDC source that represents PRV positon.
Potentiometer rotation is limited to 37 degrees. PRV

position is displayed on the COMPRESSOR Screen
as 0 (closed) to 100% (fully open). Positions between
these extremes are linearly scaled. To assure position
ac cu ra cy, a calibration procedure must be performed as
de tailed in the “System Calibration, Service Setpoints
and Reset Procedures” section of this book. The PRV
po si tion is transmitted to the Microboard via the RS-485
serial communications link.

The Analog I/O Board must be con

fi

gured properly for

the Hot Gas control. The on-board Program Jumpers
must be con

fi

gured as follows:

JUMPER POSITION

  J1   Pins 2 & 3
J26    Pins 2 & 3
J39    Pins 1 & 2

There must be a 499 Ohm, 1%, ½ watt resistor con-
nect ed between P10-2 and P10-5. This converts the
normal 4-20mA Analog I/O Board output to a 2-10VDC
valve positioning output, required by the Hot Gas valve
actuator.

«
...
125
126
127
128
129
...
»

Содержание MAXE OPTIVIEW YK





















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAXE OPTIVIEW YK

Бренд: SMC Networks Страницы: 9

Бренд: Land Pride Страницы: 38

Бренд: Land Pride Страницы: 36

Бренд: Qualcast Страницы: 14

Бренд: Garland Страницы: 172

Бренд: MK Martin Страницы: 11

215-412-000, 215-418-000, GRT8

Бренд: MTD Страницы: 28

Бренд: Hansa Страницы: 30

Бренд: Lauda Страницы: 23

Бренд: GreenWorks Pro Страницы: 30

HYDROPONIC HY 1000

Бренд: TecoPonic Страницы: 98

Бренд: EarthQuake Страницы: 20

Бренд: Landoll Страницы: 148

Бренд: Lawn Solutions Страницы: 8

Бренд: Honda Страницы: 46

Бренд: York Страницы: 60

Бренд: EarthQuake Страницы: 20

Бренд: York Страницы: 178

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды