York eco YCAS Series Скачать руководство пользователя страница 156

Страница: 156 / 232

156

YORK INTERNATIONAL

FORM 201.18-NM9 (602)

INSTALLATION INSTRUCTIONS FOR

VMC SERIES AWR/AWMR AND CP

RESTRAINED MOUNTINGS

1. Floor should be level and smooth.
2. For indoor applications, isolators do not normally

require bolting. If necessary, anchor isolators to

floor through bolt holes in base plate.

IMPOR-

TANT: Isolators must be bolted to substructure

and equipment to isolators when used under

outdoor equipment exposed to wind forces.

3. Lubricate threads of adjusting bolt. Loosen hold

down bolts to allow for isolator adjustment.

4. Block the equipment 1/4" higher than the speci-

fied free height of the isolator. To use the isolator

as blocking for the equipment, insert a 1/4" shim

between the upper load plate and vertical uprights.

Lower the equipment on the blocking or shimmed

isolators.

5. Complete piping and fill equipment with water, re-

frigerant, etc.

6. Turn leveling bolt of first isolator four full revolu-

tions and proceed to each mount in turn.

7. Continue turning leveling bolts until equipment is

fully supported by all mountings and equipment is

raised free of the spacer blocks or shims. Remove

blocks or shims.

8. Turn leveling bolt of all mountings in either direc-

tion in order to level the installation.

9. Tighten nuts on hold down bolts to permit a clear-

ance of 1/8" between resilient washer and under-

side of channel cap plate.

10. Installation is now complete.

Technical Data

Содержание eco YCAS Series









































































































































































































































Результаты поиска

Содержание eco YCAS Series

Отзывы:

Похожие инструкции для eco YCAS Series

Бренды по названию

Популярные бренды

York eco YCAS Series, Руководство пользователя

Результаты поиска

Содержание eco YCAS Series

Отзывы:

Похожие инструкции для eco YCAS Series

Бренды по названию

Популярные бренды