York D12100 Скачать руководство пользователя

Страница: 39 / 78

Assembly

GLOBAL

INDUSTRIES, INC.

Drag Conveyors

10230011

2016-06-14

Covers

put the covers on

Conveyor covers are hemmed at the ends for

easy installation. After the chain is properly

installed, bolt on the covers (examples c and d).

Use 3/8” x 1” bolts with seal washers and

3/8” fl ange nuts. Covers do not require caulking.

First start installing covers at the conveyor tail.

Set the folded seams down on top over standing

seams. Continue working forwards until the

last cover is installed on the conveyor head.

(Conveyor chain is already fully installed but is

not shown in these examples.)

NOTE: Conveyors shown in this manual may look

different than your conveyor.

d) Bolt Covers on Correctly

COVER

3/8”

FLANGE

NUT

INTERMEDIATE

SECTION

3/8” x 1” BIN BOLT

WITH SEAL WASHER

towards

head

section

COVER

INTERMEDIATE

SECTION

FOLDED

SEAM

STANDING

SEAM

c) Install the Head Cover

3/8” x 1” BIN BOLT

WITH SEAL WASHER

INTERMEDIATE

COVER

HEAD

COVER

INTERMEDIATE

SECTION

HEAD

SECTION

3/8”

FLANGE

NUT

Содержание D12100















































































Результаты поиска

Содержание D12100

Отзывы:

Похожие инструкции для D12100

Бренды по названию

Популярные бренды

York D12100, Руководство пользователя

Результаты поиска

Содержание D12100

Отзывы:

Похожие инструкции для D12100

Бренды по названию

Популярные бренды