manualshive.com logo in svg

York D12100, Руководство пользователя, Страница: 67 / 78

Поделиться
Скачать
York D12100 Скачать руководство пользователя страница 67

Appendix

67

GLOBAL

INDUSTRIES, INC.

Drag Conveyors 

  10230011

2016-06-14

reduced rated 

capacity

 (low capacity)

obstructions at conveyor inlets, 

bins, hoppers, or chutes feeding the 

conveyor

remove obstruction

clumping of moist material on the 

paddles or along trough sides which 

are effectively reducing conveyor 

capacity

remove clumping

possible damage to chain or paddles 

due to foreign object caught in the 

conveyor

check conveyor and replace any damaged or 

broken paddles, attachments, or chain / remove 

any foreign objects and replace any damaged parts 

(don’t attempt to reweld attachments onto the 

chain) heat treated chain attachments can become 

brittle and crack resulting in chain breakage

 chain too loose

adjust take-up for proper chain tension

improper chain speed

check shaft rpm / adjust it if needed

plugging

discharges are clogged / check them and unplug 

as needed

material size and shape

the material may be restrictive / alter fl ow 

accordingly

reducer 

overheating

low or overfi lled gear lubricant

not fi lled according to manufacturer’s 

recommendations / refi ll

wrong grade or weight of lubricant

see manufacturer’s recommendations / refi ll

reducer overloaded

wrong size reducer / obtain proper size

reducer failing

worn gears or failed bearings

 start-up problem

the drive wasn’t furnished by 

MFS/YORK/STORMOR and is of a 

different capacity or output then 

specifi cations require for this 

conveyor

obtain the correct drive

the conveyor’s specifi ed capacity in 

terms of volume or cubic footage is 

being exceeded

adjust input capacity

the conveyor is being used to handle 

a different material than it was 

originally specifi ed for

make the needed changes to the conveyor so it 

can handle the material or use the conveyor for 

another material

uneven  sprocket 

wear

worn chain

replace chain / see chain section

improper alignment

correct conveyor alignment

material carry-over into discharge 

sprocket

check for and correct improperly located inlet

uneven uhmw 

paddle wear

conveyor not aligned correctly

correct alignment

sprocket slipped

adjust sprocket and tighten set screws

Содержание D12100















































































Отзывы:

Нет отзывов