manualshive.com logo in svg

YOKOGAWA WE7281, Руководство пользователя, Страница: 25 / 52

Поделиться
Скачать
YOKOGAWA WE7281 Скачать руководство пользователя страница 25

2-4

IM 707281-01E

2.2  Connecting the Output Signal Wire

When connecting the output signal wire to the clamp type terminal, loosen the screw

holding down the clamp, insert the output signal wire into the opening, and then tighten

the screw.

Recommended length of the stripped portion of the output signal wire: 7 mm

Thickness of the output signal wire (for twisted wire)

: 0.5 to 1.5 mm

2

Clamping screw

For WE7282

Use a BNC cable for the output signal.  The BNC cable is connected to the output

terminal (isolated BNC) on the front panel of the module.  There are four channels of

output terminals.

CAUTION

• Do not apply voltages that exceed the following values, as it may damage the

module.

Maximum common mode voltage:

±

42.4 VDC+ACpeak between the ground and

the L terminal

Maximum voltage between channels:

±

42.4 VDC+ACpeak between terminals of

different channels

Note

The maximum length of the cable that is connected to the output connectors of WE7281/WE7282

is 20 m.  However, if the cable length exceeds 3 m, undesirable effects such as delay in the rise

time of the output waveform or distortion may occur.

OUTPUT

10V

CH1

CH2

CH3

CH4

Содержание WE7281





















































Отзывы:

Нет отзывов