YOKOGAWA TB750G Скачать руководство пользователя страница 3

Страница: 3 / 37

IM 12E01A06-02E

<Introduction>



Notice

About this Manual

This manual should be passed on to the end user.

This manual should be read thoroughly before operating the instrument.

This manual explains the functions contained in this product, but does not warrant that they will suit

the particular purpose of the user.

The contents of this manual shall not be reproduced or copied, in part or in whole, without permis

sion.

The contents of this manual are subject to change without prior notice.

Every effort has been made to ensure the accuracy in the preparation of this manual. However, if

any errors or omissions are noticed, please contact the nearest Yokogawa representative or sales

office.

Protection, Safety, and Modification of the Product

The safety instructions described in this manual should be strictly observed to ensure safety both

of the product and the system controlled by the product.

A protection or safety circuit should be installed externally, if needed. Do not attempt to modify or

add such circuit to the inside of the equipment.

Limitation of Liability

Yokogawa grants no warranties other than the express warranty set forth under the warranty pro

visions.

Yokogawa shall not be liable to you or any third party for any damage, including consequential or

incidental damages, arising out of or in connection with the use of this equipment, defects beyond

our knowledge, or any other contingency beyond our control.

Содержание TB750G






































Результаты поиска

Содержание TB750G

Отзывы:

YOKOGAWA TB750G, Быстрый старт, Страница: 3 / 37

Результаты поиска

Содержание TB750G

Отзывы: