YOKOGAWA EXAxt ZR22G Скачать руководство пользователя страница 75

Страница: 75 / 211

<4. Piping>

4-10

IM 11M12A01-02E 16th Edition : Mar. 19, 2020-00

Flange

156

Rc1/4 or 1/4NPT

Calibration gas inlet

Reference gas outlet

Flange

PIPING

Stop Valve

Rc1/4 or 1/4NPT

Reference gas inlet

2-G1/2, 2-1/2NPT etc.

Cable connection port

*1 Dimensions may vary depending on the detector type. Refer to Section 2.2

Ensure that the flange gasket does not block the reference gas outlet.

Where necessary, make a notch on the flange

F4-12E.ai

Figure 4.13

Detector with Pressure Compensation

Valve operation

(1) For safety, stop the furnace that the detector is to be installed in. If furnace internal pressure

is high, this is especially dangerous.

(2)

Before starting instrument air flow, completely shut the stop valve in front of the reference

gas outlet.

(3)

Check that the reference gas outlet is not blocked by a flange gasket or the like.

(4) Set the instrument air pressure higher than furnace internal pressure.
(5) Completely open the stop valve in front of the reference gas outlet and, after turning on

instrument air flow, start furnace operation. As furnace internal pressure rises, confirm

that instrument air continues to flow and adjust the valve or increase supply pressure if

necessary.

(6)

After furnace internal pressure stabilizes, adjust flow.

(7)

If furnace operation is stopped, stop instrument air flow and completely shut the stop valve

in front of the reference gas outlet. You may leave reference gas flowing if you wish.

CAUTION

• As far as possible do not stop the instrument air flow, to prevent the sample gas from

entering the detector and damaging the zirconia cell.

• Connect the stop valve, which is at the calibration gas inlet, directly to the detector.

If there is piping between the detector and the valve, condensation may damage the sensor

by rapid cooling when calibration gas is introduced.

Figure 4.14 illustrates an example of System 2 using a detector with pressure compensation.

Supply air pressure (flow) may vary depending on the furnace pressure. It is recommended to

use a flowmeter and an air set that is suitable for the furnace pressure.

NOTE

When using the ZA8F Flow Setting Unit and ZR40H Automatic Calibration Unit, please note that

the supplying airflow (pressure) will vary depending on the furnace pressure.

Содержание EXAxt ZR22G




















































































































































































































Результаты поиска

Содержание EXAxt ZR22G

Отзывы:

YOKOGAWA EXAxt ZR22G, Руководство пользователя, Страница: 75 / 211

Результаты поиска

Содержание EXAxt ZR22G

Отзывы: