YMGI VRFI-07EL-D2B(55)5 Скачать руководство пользователя страница 3

 

Introduction 

 

Read this manual carefully, making sure you understand all the instructions, practices and procedures contained in this manual. 
Be sure you are familiar with all the safety advisories that appear throughout this manual. Your personal safety depends upon 
your observance of all precautions contained in this manual.   
 

 
 
The 3 types of advisories are defined in the following table: 
 

 

Indicates a potentially hazardous situation which, if not avoided, could result in serious 
injury or even death.

 

 

 

Indicates a potentially hazardous situation which, if not avoided, could result in minor or 
moderate injury. It is also used to alert against unsafe practices.

 

 

 

Indicates a situation that could result in equipment or property-damage only. It can also 
be used to call attention to important details within this manual.

 

  

Important Environmental Concerns 

Studies have shown  that  certain man-

made chemicals can affect the earth’s stratospheric ozone layer when released into the 

atmosphere. Refrigerants that contain Chlorine, Fluorine and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine 
and Carbon (HCFCs), may affect the ozone layer. Not all refrigerants have the same potential impact on the environment. YMGI 
Group advocates for the responsible handling of all refrigerants including industry replacements for CFCs such as HCFCs and 
HFCs. 

Responsible Refrigerant Practices

 

YMGI  Group  believes  that  responsible  refrigerant  practices  are  important  to  our  customers,  the  HVAC/R  industry  and  the 

environment. All HVAC/R technicians who handle refrigerants must be certified. The Federal Clean Air Act (Section 608) sets forth 
the requirements for handling, reclaiming, recovering and recycling of certain refrigerants, the equipment and tools necessary to 
perform these service procedures. In addition, some states or municipalities may have additional requirements that must also be 
adhered to for responsible management of refrigerants. HVAC/R technicians must know the applicable laws and follow them. 

 

Disposal Notice 

 

Do not dispose of this product or its components as unsorted municipal waste, as they contain items that may require special 
treatment. Contact your local waste management company for details. 
 

 

Proper Field Wiring and Grounding Required! 

Failure  to  follow  established  electrical  codes  can  result  in  death,  serious  personal  injury  and  property  damage.  All  field  wiring 

MUST be performed by qualified personnel, such as a currently licensed electrician. Improperly installed and grounded field wiring 
poses 

FIRE

  and 

ELECTROCUTION

  hazards.  To  avoid  these  hazards,  you  MUST  follow  the  requirements  for  field  wiring 

installation and grounding as described in this manual, by NEC and your state/local electrical codes. 

 

 

Personal Protective Equipment (PPE) Required!

 

Failure to wear proper PPE for the job being undertaken could result in serious injury or even death. Technicians must take the 
necessary  precautions  to  protect  themselves  from potential  electrical,  mechanical,  and  chemical  hazards  and  MUST  follow  all 
precautions in this manual and on the tags, stickers, and labels, as well as the instructions below: 

 

Before installing or servicing this unit, technicians MUST put on all PPE recommended for the work being undertaken. 
ALWAYS refer to appropriate Material Safety Data Sheets (MSDS) and Occupational Safety and Health Administration 
(OSHA) guidelines for proper PPE.  

 

When working with or around hazardous chemicals, ALWAYS refer to the appropriate MSDS sheets and OSHA guidelines 
for information on allowable personal exposure levels, proper respiratory protection, and handling recommendations.  

If  there  is  a  risk  of  arc  or  flash,  technicians  MUST  put  on  all  PPE  in  accordance  with  NFPA  70E  or  other  country-specific 
requirements for arc flash protection, PRIOR to servicing the unit. 

 

Copyright 

This document and the information contained therein are the sole property of YMGI Group and shall not be used or 
reproduced  in  whole  or  in  part,  without  the  written  permission  of  YMGI  Group.  YMGI  Group  reserves  the  right  to 
revise  this  manual  at  any  time  and  to  make  changes  to  its  content  without  obligation  to  notify  anyone  about  any 
modifications, revisions or changes.  
 

Содержание VRFI-07EL-D2B(55)5





































Отзывы: