YATO YT-82007, Оригинальное руководство пользователя

Страница: 15 / 116

15
O R I G I N A L I N S T R U C T I O N S
EN
TRANSPORT, MAINTENANCE AND STORAGE
Caution! Disconnect the sparking plug cable before installing, adjusting, replacing accessories or storing the device.
This will allow for avoiding accidental turning on of the device.
When not in use, store the device in a dry, secured place inaccessible to unauthorised
persons.
Before transporting the device, it is necessary to empty the fuel tank.
Replace worn or damaged parts to ensure the safety. Use original spare parts only. Failure to use original spare parts may in-
crease the risk of failure and lead to body injuries. The device should be repaired only at authorised service centres using original
spare parts. This will minimise the risk of accidents and damage to the equipment.
Store the device in a well-ventilated dry and closed room. When stored for a longer period, empty the fuel tank and the fuel sys-
tem. Do not store the device with fuel in the tank. The device should also undergo the maintenance procedures described in the
instructions manual.
When transporting the device, remove the insertion tool.
Keep all nuts, bolts and screws in good condition to ensure safe device operation.
ADDITIONAL SAFETY INSTRUCTIONS
Wear hearing protectors. Exposure to noise can cause hearing loss.
Use the device with the additional handles provided with the tool. Loss of control can cause personal operator injuries.
When carrying out work during which insertion tool may come into contact with a live, concealed electrical wire or power
supply cable, hold the electrical tool using isolated handles. When the insertion tool is in contact with a live wire, it may cause
the metal parts of the tool to become live, which may lead to an electric shock to the tool operator.
Safety warnings related to drilling with long bits
Always start drilling at low speed so that the bit end has a contact with the workpiece. At higher speeds, the bit will probably
bend and cause injury if it is allowed to rotate freely without contact with the workpiece.
Apply pressure only in a straight line with the bit and do not apply excessive pressure. The bit can bend causing breakage
and loss of control which will result in injury.
HAMMER OPERATION
Preparing for operation
Unpack the device and remove all elements of the packaging. It is recommended to keep the original packaging, as it can be
helpful for further transport and storage of the device.
Select the right work tool: punch or cutter.
Clean the tool, lubricate the holder of the selected tool with a thin layer of grease.
Wear hearing protectors, eye protection, and work gloves.
The insertion tool in the form of chisel, cutter or punch is locked in the holder with a rotating lock.
Pull out the tool holder lock and rotate it 180 degrees so that the lock is not an obstacle when inserting and removing the work
tool into or from the holder (II).
The hexagonal holder on one wall has a groove that allows the holder lock to be rotated and the work tool to be locked in the
holder. Insert the work tool into the holder so that the groove is at the height of the lock (III). Then pull out the tool holder lock and
rotate it 180 degrees to prevent the tool from sliding out of the tool holder. Make sure to grip the tool and try to pull it out of the
holder. If you can remove the tool, it must be reinstalled according to the procedure.
To remove an insertion tool, follow the installation procedure in reverse order.
Refuelling
When preparing the refuelling device, it must be positioned in such a way that the fuel fi ller of the tank is facing upwards.
The fuel mixture intended for two-stroke engines is used to drive the device. It is forbidden to use petrol alone. Petrol should
be mixed with oil in the following ratio: petrol : oil - 25 : 1. The mixture should be mixed before pouring into the fuel tank. Mixing
and pouring fuel should be carried out away from fi re sources. Never smoke while refuelling. Refuelling must be carried out at a
distance of at least 3 metres from the starting and work area of the device.
In order to protect the engine, use good quality unleaded petrol and good quality oil for two-stroke air-cooled engines. Do not use
oil intended for four-stroke engines. Do not use oil for liquid-cooled engines.
In case of spilling the fuel, thoroughly wipe o ff its residues before starting the device.
Do not use a mixture older than 30 days.
After re fi lling the tank, close its fi ller fi rmly and securely.