YASKAWA SI-EP3, Техническое руководство

Страница: 25 / 58

6 Related Drive Parameters
YASKAWA ELECTRIC SIEP C730600 89C YASKAWA AC Drive Option SI-EP3 Technical Manual 25
F7-24
(03FC)
<12>
Dynamic Output Assembly
Parameter 2
Sets configurable output 2.
Default: 0H
Min.: 0H
Max.: FFFFH
F7-25
(03FD)
<12>
Dynamic Output Assembly
Parameter 3
Sets configurable output 3.
Default: 0H
Min.: 0H
Max.: FFFFH
F7-26
(03FE)
<12>
Dynamic Output Assembly
Parameter 4
Sets configurable output 4.
Default: 0H
Min.: 0H
Max.: FFFFH
F7-27
(03FF)
<12>
Dynamic Output Assembly
Parameter 5
Sets configurable output 5.
Default: 0H
Min.: 0H
Max.: FFFFH
F7-33
(0375)
<12>
Dynamic Input Assembly
Parameter 1
Sets configurable input 1.
Default: 0H
Min.: 0H
Max.: FFFFH
F7-34
(0376)
<12>
Dynamic Input Assembly
Parameter 2
Sets configurable input 2.
Default: 0H
Min.: 0H
Max.: FFFFH
F7-35
(0377)
<12>
Dynamic Input Assembly
Parameter 3
Sets configurable input 3.
Default: 0H
Min.: 0H
Max.: FFFFH
F7-36
(0378)
<12>
Dynamic Input Assembly
Parameter 4
Sets configurable input 4.
Default: 0H
Min.: 0H
Max.: FFFFH
F7-37
(0379)
<12>
Dynamic Input Assembly
Parameter 5
Sets configurable input 5.
Default: 0H
Min.: 0H
Max.: FFFFH
H5-11
(043C)
Communications ENTER Function
Selection
Selects whether an Enter command is necessary to change parameter
values via MEMOBUS/Modbus communications.
0: Parameter changes are activated when ENTER command is written
1: Parameter changes are activated immediately without use of ENTER
command
Default: 0
<13>
Range: 0, 1
<1> Set b1-02 = 3 to start and stop the drive with the PROFINET master device using serial communications.
Set b1-01 = 3 to control the frequency reference of the drive via the master device.
<2> Setting this parameter to 3 or 4 will cause the drive to continue operation after detecting a fault. Take proper measures such as installing an
emergency stop switch when using settings 3 or 4.
<3> Refer to the drive manual to know if settings 4 and 5 are available. Settings 4 and 5 are available in A1000 software versions PRG: 1021 and
later.
<4> The setting range for 1000-Series drives is different for different software versions. Refer to the instruction manual of a specific drive for more
information.
<5> Control method availability of this parameter depends on product series.
 1000-Series Drives: Parameter is available in CLV, AOLV/PM, and CLV/PM.
In AOLV/PM, this value is read as the Torque Limit.
 GA700, GA800 Drives: Parameter is available in OLV, CLV, AOLV, AOLV/PM, CLV/PM, and EZOLV.
In OLV and EZOLV, this value is read as the Torque Limit.
<6> The setting specifies that network communications provide the torque reference or torque limit. The motor may not rotate if the PLC does not
supply a torque reference or torque limit.
<7> Not available on 1000-series drives.
<8> Cycle power for setting changes to take effect. Set F6-15 to 1 (Enable), to have settings take effect immediately on non-1000 series drives.
<9> Set F7-01 to F7-04 when F7-13 is set to 0. All IP Addresses (F7-01 to F7-04) must be unique.
<10> Set F7-01 to F7-12 when F7-13 is set to 0.
<11> Set F7-15 when F7-14 is not set to 1.
<12> If a value other than 0 is assigned to parameters F7-23 to F7-27 and F7-33 to F7-37 by the drive, that value will take precedent over a value set
by the configuration software. If the value in the drive is 0 (default), the value from the configuration software is used.
<13> The default setting is different for different product series. Refer to the instruction manual of a specific drive for more information.
No.
(Hex.)
Name Description Values