YASKAWA Motoman MH Series Скачать руководство пользователя страница 36

Страница: 36 / 116

INSTALLATION

MH–Series Positioner Manual with MotoMount

4-12

MOTO

MAN

4.4

Tailstock Column Installation

4.4.1

Type I Installation

Before proceeding to install the tailstock, make sure the Type I headstock is
already anchored to the floor. If it is not, refer to Section 4.2.

To install the tailstock onto a cell base or floor, proceed as follows:

1. Ensure the proper position of the headstock assembly per system layout. The

headstock must be permanently anchored to the floor/base.

2. Using a carpenter’s chalk string, strike a chalk line on the floor from the edge

of the headstock base toward the location of the tailstock (see Figure 4-12).

Figure 4-12 Strike Chalk Line

3. Set the tailstock in its approximate position on the floor using the chalk line.

The headstock and tailstock are now facing each other.

4. Measure the distance (D) between the headstock and tailstock base. To find

the distance (D) between the headstock base and tailstock base (see Figure 4-
13), use the following tailstock mounting formula:

D = PD + X (PD = Tooling pin-to-pin distance; X = MotoMount Offset)

NOTE:

The placement position derived from this formula will position the tailstock in the nominal
center position.

5. To find the X value in the tailstock mounting formula for your drive

assembly, locate the drive assembly model name in Table 4-3.

Figure 4-13 Tailstock Placement without Tooling – Type I

Table 4-3 Column Installation – X value

Type I System

X - value

MHT75/150 - mm (in)

-38 (-1.46)

MHT340 - mm (in)

61 (2.40)

MHT450 - mm (in)

57 (2.24)

MHT1500 - mm (in)

156 (6.14)

MHT1000/3000 - mm (in)

138 (5.43)

CHALKLINE

HEADSTOCK
COLUMN BASE

TAILSTOCK
COLUMN BASE

CHALKLINE

Содержание Motoman MH Series





















































































































Результаты поиска

Содержание Motoman MH Series

Отзывы:

Похожие инструкции для Motoman MH Series

Бренды по названию

Популярные бренды

YASKAWA Motoman MH Series, Руководство пользователя

Результаты поиска

Содержание Motoman MH Series

Отзывы:

Похожие инструкции для Motoman MH Series

Бренды по названию

Популярные бренды