YASKAWA Motoman MH Series Скачать руководство пользователя страница 32

Страница: 32 / 116

INSTALLATION

MH–Series Positioner Manual with MotoMount

4-8

MOTO

MAN

4.3

Installing the MH-Series Drive Assembly – Type II

4.3.1

Site Preparation

Each MH-Series drive assembly should be firmly mounted on a machine base or
foundation rigid enough to withstand static and dynamic forces.

4.3.2

Unpacking

The headstock and optional tailstock are shipped on a wood shipping skid. To
unpack the equipment, proceed as follows:

WARNING!

The MH-series headstock can weigh as much as 1200 kg (2650 lbs).
Be sure that your lifting device is capable of handling this much
weight or damage to the equipment or injury to personnel can result.

1. Carefully remove protective plastic wrapping from equipment.
2. Inspect equipment for shipping damage.

NOTE:

If any equipment is damaged, notify the shipper immediately.

3. Unbolt headstock from wooden shipping skid (see Figure 4-8) using a 3/4-

inch socket.

Figure 4-8 Unbolting the Drive Assembly

WOOD
SHIPPING SKID

SHIPPING BOLT

Содержание Motoman MH Series





















































































































Результаты поиска

Содержание Motoman MH Series

Отзывы:

Похожие инструкции для Motoman MH Series

Бренды по названию

Популярные бренды

YASKAWA Motoman MH Series, Руководство пользователя

Результаты поиска

Содержание Motoman MH Series

Отзывы:

Похожие инструкции для Motoman MH Series

Бренды по названию

Популярные бренды