Yanmar YDG Series Скачать руководство пользователя страница 40

Страница: 40 / 92

BEFORE YOU OPERATE

YDG Operation Manual

Figure 3

3. When connecting cables to battery connect the

positive (+) cable (1,

Figure 4

)

first.

CAUTION

When you install a battery, always use
correct polarity when you connect battery
cables to the battery. Always make sure the
battery terminals are clean and tight.

4. Connect the negative (–) cable (2,

Figure 4

) to

the battery last.

Figure 4

DIESEL FUEL

Diesel Fuel Specifications

Diesel fuel should comply with the following
specifications. The table lists several worldwide
specifications for diesel fuels.

NOTICE

Always use diesel fuels recommended by
YANMAR for the best engine performance, to
prevent engine damage. Only use clean diesel fuel.



Additional technical fuel requirements

• The fuel cetane number should be equal to 45 or

higher.

• The sulfur content must not exceed 0.5 % by

volume. Less than 0.05 % is preferred.

• Bio-diesel fuels.

See Bio-diesel fuels on page 27

• Never mix kerosene, used engine oil, or residual

fuels with the diesel fuel.

• Water and sediment in the fuel should not exceed

0.05 % by volume.

• Keep the fuel tank and fuel-handling equipment

clean at all times.

• Poor quality fuel can reduce engine performance

and/or cause engine damage.

• Fuel additives are not recommended. Some fuel

additives may cause poor engine performance.
Consult your YANMAR industrial engine dealer or
distributor for more information.

(+)

(-)

(+)

(-)

Diesel fuel specification

Location

EN590:96

European Union

ISO 8217 DMX

International

BS 2869-A1 or A2

United Kingdom

JIS K2204 grade No.2

Japan

KSM-2610

Korea

GB252 China

Содержание YDG Series





























































































Результаты поиска

Содержание YDG Series

Отзывы:

Похожие инструкции для YDG Series

Бренды по названию

Популярные бренды

Yanmar YDG Series, Руководство по эксплуатации

Результаты поиска

Содержание YDG Series

Отзывы:

Похожие инструкции для YDG Series

Бренды по названию

Популярные бренды