Yanmar YDG Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 92

Yanmar YDG Series Скачать руководство пользователя страница 18

SAFETY

4

YDG Operation Manual

DANGER

Fire Hazard

• Never use metal pipe that carries

combustible materials or gases to
ground the generator.

• Do not put the generator indoors while the

engine is still hot.

• Never jump-start the engine. Sparks caused

by shorting the battery to the starter terminals
may cause a fire or explosion.

• Never operate the generator if powered items

overheat, electrical output drops, there is
sparking, flames or smoke coming from the
generator or if the receptacles are damaged.

• Never operate the generator closer than

3.3 ft (1 m) away from buildings and other
equipment or sources of combustion during
operation.

Falling Hazard

Avoid injury or equipment damage due to the
generator set falling. Always secure the
generator set to prevent the generator set from
falling during maintenance.

WARNING

Explosion Hazard

• Avoid serious personal injury or

equipment damage. While the
engine is running or the battery is
charging, hydrogen gas is being
produced and can be easily
ignited. Keep the area around the
battery well-ventilated and keep
sparks, open flame and any other
form of ignition out of the area.

• Avoid serious personal injury or equipment

damage. Always turn off the battery switch (if
equipped) or disconnect the negative battery
cable before servicing the equipment.

Fire Hazard

• Avoid personal injury or

equipment damage. Have
appropriate safety equipment
available.

• Keep fire extinguishers handy in case of fire.

Clearly indicate the location of the fire
extinguishers with a safety sign.

• Ensure that the type of fire extinguishers are

appropriate for material that might catch fire.
Check with local authorities.

• Have all fire extinguishers checked

periodically for proper operation and/or
readiness.

• Post evacuation routes prominently.

Periodically conduct fire drills.

Avoid personal injury. Always read and follow
safety-related precautions found on containers
of hazardous substances like parts cleaners,
primers, sealants and sealant removers.

Always wipe up all spills immediately.

The user must comply with safety regulation
applicable in the place where the genset has
been sold.

«
...
16
17
18
19
20
...
»

Содержание YDG Series





























































































Отзывы:

Нет отзывов