background image

 

© Yanmar 2008  

Page  7

Electronic Control System:  

Operation Manual for SY Series Engines with GEN III Controls 

Appendix A

User Settings and Factory Settings

  The user setting allows for reset of the maintenance timer.

  The factory settings require a password to change.  

“Unlocking” the Hot Keys 

This is a popular way to expand the use of the i5601E. To unlock the hot keys and allow for additional data 

selections go to the Main menu, as described on page 16.  Then select HOT KEYS.  Exit the menu back to the 

normal operating screens.  You will see a right hand arrow above key 5 when any key is pressed. 
The Right Arrow button changes the menu to allow selection of each block.  Pressing a block key will cycle 

through the choices listed on the next page. The choices are presented in alphabetical order. Bold items are the 

default settings and will appear initially unless replaced by an indented item listed underneath.

note: Data in nMEA 2000

®

 format may be added to the CANBus system from a compatible device which 

feeds the optional parameters listed above.  The i5601E display has the capability of displaying additional 

information as other devices with NMEA 2000® communication capabilities are added to the vessel.

Example using a quad screen:  

5

Hot Keys

5

Block Keys

Each button cycles the related block 

through the list on the next page.

Содержание i8350





























Отзывы: