Yanmar i8350 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 28

background image

Page 4

© Yanmar 2008

Electronic Control System:

Operation Manual for SY Series Engines with GEN III Controls

i8350/55 Operation

i8350/55 Engine Interface Module

The switches inside the i8350/55 allow for starting and stopping the engine.

•

Turn on the ignition switch at the helm.

•

To start the engine, turn on Emergency Start Power by pressing

in the top of the Emergency Start Power Switch. The buzzer

will sound.

•

Start the engine by pressing in the top of the Emergency

Engine Start Switch.

•

Stop the engine by pressing the RED “Stop” button.

For indicator light information, see page 13.

Programming connector.

Factory use only.

Important Note:

No service items

exist behind this

panel.

Removal of this

panel will void

the warranty

«
...
14
15
16
17
18
...
»

Содержание i8350





























Отзывы:

Нет отзывов

Похожие инструкции для i8350

Бренд: Samson Страницы: 20

Бренд: 2gig Technologies Страницы: 4

Бренд: 2gig Technologies Страницы: 2

Бренд: G1SLE Страницы: 2

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: Faulhaber Страницы: 66

Бренд: National Instruments Страницы: 29

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: olympia electronics Страницы: 10

Бренд: Vega Страницы: 20

dmc1 Finish-Out

Бренд: M&S Systems Страницы: 8

Бренд: Zamel Страницы: 23

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды