Yanmar 6LPA-STP2 Скачать руководство пользователя страница 9

Страница: 9 / 110

SAFETY

Yanmar considers safety of great

importance and recommends that anyone

that comes into close contact with its

products, such as those who install,

operate, maintain or service Yanmar

products exercise care, common sense and

comply with the safety information in this

manual and on the engine’s safety decals.

Keep the decals from becoming dirty or torn

and replace them if they are lost or

damaged. Also, if you need to replace a part

that has a decal attached to it, make sure

you order the new part and decal at the same

time.

This safety alert symbol appears

with most safety statements. It

means attention, become alert,

your safety is involved! Please

read and abide by the message

that follows the safety alert

symbol.

DANGER

Indicates a hazardous situation which, if

not avoided, will result in death or

serious injury.

WARNING

Indicates a hazardous situation which, if

not avoided, could result in death or

serious injury.

CAUTION

Indicates a hazardous situation which, if

not avoided, could result in minor or

moderate injury.

NOTICE

Indicates a situation which can cause

damage to the engine, personal property

and / or the environment or cause the

equipment to operate improperly.

6LPA Series Operation Manual

Содержание 6LPA-STP2















































































































Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды

Yanmar 6LPA-STP2, Руководство по эксплуатации

Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды