Yanmar 6LPA-STP2 Скачать руководство пользователя страница 105

Страница: 105 / 110

Owner’s Responsibility:

As the Yanmar Marine engine owner, you

are responsible for the performance of the

required maintenance listed in your

Operation Manual. Yanmar recommends

that you retain all documentation, including

receipts, covering maintenance on your

marine engine, but Yanmar cannot deny

warranty solely for the lack of receipts or for

your failure to ensure the performance of all

scheduled maintenance.

Your engine is designed to operate on diesel

fuel only. Use of any other fuel may result in

your engine no longer operating in

compliance with applicable emission

requirements. You are responsible for

initiating the warranty process. You must

present your marine engine to an authorized

Yanmar dealer or distributor as soon as a

problem exists.

Customer Assistance:

If you have any questions regarding your

warranty rights and responsibilities or would

like information on the nearest authorized

Yanmar dealer or distributor, you should

contact Yanmar Marine USA Corporation for

assistance.

Yanmar Marine USA Corporation

101 International Parkway

Adairsville, GA 30103 USA

Telephone: 770-877-9894

Fax: 770-877-7567

EPA WARRANTY USA ONLY

6LPA Series Operation Manual

Содержание 6LPA-STP2















































































































Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды

Yanmar 6LPA-STP2, Руководство по эксплуатации

Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды