Yanmar 6LPA-STP2 Скачать руководство пользователя страница 10

Страница: 10 / 110

SAFETY PRECAUTIONS

General Information

There is no substitute for common sense

and careful practices. Improper practices or

carelessness can cause burns, cuts,

mutilation, asphyxiation, other bodily injury

or death. This information contains general

safety precautions and guidelines that must

be followed to reduce risk to personal safety.

Special safety precautions are listed in

specific procedures. Read and understand

all of the safety precautions before operation

or performing repairs or maintenance.

Before You Operate

DANGER

The safety messages that follow have

WARNING level hazards.

NEVER permit anyone to

install or operate the

engine without proper

training.

• Read and understand this Operation

Manual before you operate or service the

engine to ensure that you follow safe

operating practices and maintenance

procedures.

• Safety signs and labels are additional

reminders for safe operating and

maintenance techniques.

• See your authorized Yanmar Marine

dealer or distributor for additional training.

During Operation and

Maintenance

DANGER

The safety message that follows has

DANGER level hazards.

Crush Hazard

NEVER stand under hoisted

engine. If the hoist mechanism

fails, the engine will fall on you.

SAFETY

6LPA Series Operation Manual

Содержание 6LPA-STP2















































































































Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды

Yanmar 6LPA-STP2, Руководство по эксплуатации

Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды