Yanmar 6LPA-STP2 Скачать руководство пользователя страница 78

Страница: 78 / 110

Periodically operate the engine near

maximum speed while underway. This

will generate higher exhaust

temperatures, which will help clean out

hard carbon deposits, maintain engine

performance and prolong the life of the

engine.

Are there abnormal vibrations or noise?

• Depending on the hull structure, engine

and hull resonance may suddenly

increase at certain engine speed ranges,

causing heavy vibrations. Avoid operation

in this speed range. If any abnormal

sounds are heard, stop the engine and

inspect for cause.

Alarm sounds during operation.

• If the alarm sounds during operation,

lower the engine speed immediately,

check the warning lamps and stop the

engine for repairs.

Is there water, oil or fuel leakage? Are

there any loose bolts or connections?

• Check the engine room daily for any leaks

or loose connections.

Is there sufficient fuel in the fuel tank?

• Refill fuel in advance to avoid running out

of fuel. If the tank runs out of fuel, bleed

the fuel system. See Bleeding the Fuel

System on page 30.

TROUBLESHOOTING

6LPA Series Operation Manual

Содержание 6LPA-STP2















































































































Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды

Yanmar 6LPA-STP2, Руководство по эксплуатации

Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды