Yanmar 6LPA-STP2 Скачать руководство пользователя страница 54

Страница: 54 / 110

WARNING

Welding Hazard

Make welding repairs safely.

• ALWAYS turn off the battery switch (if

equipped) or disconnect the negative

battery cable and the leads to the

alternator when welding on the

equipment.

• Remove the multi-pin connectors to the

engine electronics or engine control unit.

Connect the weld clamp to the

component to be welded and as close as

possible to the welding point.

• NEVER connect the weld clamp to the

engine or in a manner which would allow

current to pass through a mounting

bracket.

• When welding is completed, reconnect

the leads to the alternator and engine

electronics or engine control unit prior to

reconnecting the batteries.

Exhaust Hazard

ALWAYS ensure that all

connections are tightened to

specifications after repair is

made to the exhaust system.

All internal combustion

engines create carbon monoxide gas during

operation and special precautions are

required to avoid carbon monoxide

poisoning.

Shock Hazard

ALWAYS turn off the

battery switch (if

equipped) or disconnect

the negative battery cable

before servicing the

equipment.

ALWAYS keep the electrical connectors

and terminals clean. Check the electrical

harnesses for cracks, abrasions, and

damaged or corroded connectors.

PERIODIC MAINTENANCE

6LPA Series Operation Manual

Содержание 6LPA-STP2















































































































Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды

Yanmar 6LPA-STP2, Руководство по эксплуатации

Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды