Yanmar 6LPA-STP2 Скачать руководство пользователя страница 35

Страница: 35 / 110

Fuel System

0004489

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

Figure 3

1 – Fuel Filter

2 – To Fuel Injection Pump

3 – Less than 500 mm (20 in.)

4 – Fuel Cock

5 – 20 - 30 mm (0.75 - 1.125 in.)

Approximately

6 – Drain Cock

7 – Fuel Tank

8 – Fuel Return Line
Install a fuel line from the fuel tank to the fuel

pump. See (Figure 3).

Filling the Fuel Tank

Before filling fuel tank for the first

time:

Rinse fuel tank with kerosene or diesel fuel.

Dispose of waste properly.

To fill the fuel tank:

WARNING! Operate bilge ventilation

(blowers) for a minimum of 5 minutes to

purge fumes from engine compartment

after refueling. Never operate bilge

blower while refueling. Doing so can

pump explosive fumes into the engine

compartment and result in an explosion.

1. Clean the area around the fuel cap.
2. Remove the fuel cap from the fuel tank.
3. Fill the tank with clean fuel free of oil and

dirt. WARNING! Hold the hose

nozzle firmly against the filler port

while filling. This prevents static

electricity buildup which could

cause sparks and ignite fuel vapors.

4. Stop fueling when the gauge shows the

fuel tank is full. NOTICE: NEVER

overfill the fuel tank.

5. Replace the fuel cap and hand-tighten.

Over-tightening the fuel cap will

damage it.

BEFORE YOU OPERATE

6LPA Series Operation Manual

Содержание 6LPA-STP2















































































































Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды

Yanmar 6LPA-STP2, Руководство по эксплуатации

Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды