Yanmar 6LPA-STP2 Скачать руководство пользователя страница 71

Страница: 71 / 110

Intercooler

(4)

0004917

Figure 11

Engine Oil Cooler

(2)

0004920

Figure 12

Engine Oil Cooler

(2)

0004921

Figure 13

Location

Part

Number

Qty.

Dimensions

D x L

Fuel

Cooler

119574–

44150

0.5 x 1.0 in.

Engine

Oil Cooler

119574–

44150

0.5 x 1.0 in.

Fresh

Water

Cooler

119574–

44150

0.5 x 1.0 in.

Inter-

cooler

119574–

18790

0.5 x 1.0 in.

Note: Some marine drives have additional

zinc anodes. Check the manufacturer's

documentation for location and other

information.

Checking and Adjusting Remote

Control Cables

Note: Never adjust the high speed stop bolt

on the governor. This will void the engine

warranty.
Adjusting Engine Speed (Governor)

Remote Control Cable
See your authorized Yanmar dealer or

distributor.
Adjusting Clutch Remote Control Cable
Refer to the manufacturer's documentation.

Cleaning the Turbocharger

Contamination of the turbocharger causes

revolutions to drop and engine output to fall.

If a significant drop in engine output is noted

(10% or more), clean the turbocharger.

This should be done only by a trained and

qualified technician. See your authorized

Yanmar Marine dealer or distributor.

PERIODIC MAINTENANCE

6LPA Series Operation Manual

Содержание 6LPA-STP2















































































































Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды

Yanmar 6LPA-STP2, Руководство по эксплуатации

Результаты поиска

Содержание 6LPA-STP2

Отзывы:

Бренды по названию

Популярные бренды