Yanmar 3TNV82A Скачать руководство пользователя страница 171

Страница: 171 / 234

FAILURE DIAGNOSIS

TNV DI Service Manual

1-169

Method and Procedure of Failure Diagnosis

Work Description

1. Battery voltage check:

• Set the accelerator at the lowest position, and operate the engine.

• Measure the battery voltage using a circuit tester.

2. Check of harness continuity:

• Remove the connector of the spare speed sensor and E-ECU from the harness.

• Check the harness continuity using a circuit tester.

Terminal

Specification

Battery voltage (in the normal condition)

10 to 16 [V]

• Check the alternator.
• Replace the battery.

Check the harness for correct continuity.

→

Go to [2. Check of harness continuity:]

Terminal

Continuity

Status

Alternator P terminal (E10)
[Between E-ECU and alternator]

Available

OK: normal

Unavailable

NG: harness disconnection

Alternator IG terminal
[Between Key switch and alternator]

Available

OK: normal

Unavailable

NG: harness disconnection

Alternator B terminal
[Between battery and alternator]

Available

OK: normal

Unavailable

NG: harness disconnection

Between E10 and GND/E45/E47

Unavailable

OK: normal

Available

NG: harness short-circuited with GND

• Check if the harness is damaged, or if the wiring is correct.
• Replace the harness.

• Check the alternator.
• Replace the E-ECU.

TNV_DI_SM_A4-Troubleshooting.book 169 ページ２００７年１１月１５日　木曜日　午後５時２７分

Содержание 3TNV82A











































































































































































































































Результаты поиска

Содержание 3TNV82A

Отзывы:

Похожие инструкции для 3TNV82A

Бренды по названию

Популярные бренды

Yanmar 3TNV82A, Руководство по устранению неисправностей

Результаты поиска

Содержание 3TNV82A

Отзывы:

Похожие инструкции для 3TNV82A

Бренды по названию

Популярные бренды