Yanmar 3TNV82A Скачать руководство пользователя страница 145

Страница: 145 / 234

FAILURE DIAGNOSIS

TNV DI Service Manual

1-143

Method and Procedure of Failure Diagnosis

3. Check of harness continuity:

• Remove the accelerator sensor and E-ECU from the harness.

• Check the harness continuity using a circuit tester.

4. Check of the accelerator sensor output voltage:

• Connect the 2G eco-checker harness between E-ECU and machine’s harness (for details, see [How to

use the 2G eco-checker harness] (P.1-135) And connect the all connectors (sensors, E-ECU).

• Measure the voltage between sensor signal E35 and E28 using a circuit tester.

Terminal

Continuity

Status

Sensor signal wire E35
[Between E-ECU and sensor connector]

Available

OK: normal

Unavailable

NG: harness disconnection

Sensor GND wire E28
[Between E-ECU and sensor connector]

Available

OK: normal

Unavailable

NG: harness disconnection

Sensor 5V wire E38
[Between E-ECU and sensor connector]

Available

OK: normal

Unavailable

NG: harness disconnection

Between E35 and other terminal/GND
and between E38 and other
terminal/GND

Unavailable

OK: normal

Available

NG: harness short-circuited with GND

Between E28 and GND/E45/E47

Available

OK: normal

Unavailable

NG: harness disconnection

Between E28 and other terminals

Unavailable

OK: normal

Available

NG: harness short-circuited with another

wiring

• Check if the harness is damaged, or if the wiring is correct.
• Replace the harness.

Check the output voltage of the accelerator sensor.

→

Go to [4. Check of the

accelerator sensor output voltage:]

Voltage

Status

Action

E35

≤

0.2[V]

• Replace the harness.
• Replace the accelerator sensor.

0.2[V] < E35 < 4.6[V]

(Normal range)

Replace E-ECU.

4.6V

≤

E35

• Replace the harness.
• Replace the accelerator sensor.

• Check if the harness is damaged, or if the wiring is correct.
• Replace the harness.

Replace E-ECU.

TNV_DI_SM_A4-Troubleshooting.book 143 ページ２００７年１１月１５日　木曜日　午後５時２７分

Содержание 3TNV82A











































































































































































































































Результаты поиска

Содержание 3TNV82A

Отзывы:

Похожие инструкции для 3TNV82A

Бренды по названию

Популярные бренды

Yanmar 3TNV82A, Руководство по устранению неисправностей

Результаты поиска

Содержание 3TNV82A

Отзывы:

Похожие инструкции для 3TNV82A

Бренды по названию

Популярные бренды